Fast delivery within 72 Hours
B&R X20DS838A
8 IO-Link channels (port class A)Each IO-Link channel can be configured as a digital input or output (SIO mode)Additional digital input per IO-Link connection24 VDC and GND for sensor/actuator power s…
Shipping & Delivery
-
Courier delivery
Our courier will deliver to the specified address
2-3 Days
From $20
-
DHL Courier delivery
DHL courier will deliver to the specified address
2-3 Days
From $40
-
Warranty 1 year
-
Free 30-Day returns
Description
8 IO-Link channels (port class A)Each IO-Link channel can be configured as a digital input or output (SIO mode)Additional digital input per IO-Link connection24 VDC and GND for sensor/actuator power supplyNetTime timestamps: IO-Link data
The module is an IO-Link master that allows intelligent sensors and actuators to be connected per the IO-Link standard. The module can operate up to 8 IO-Link devices. The significant increase in cyclic data with this product variant enables optimal operation of IO-Link devices. Flatstream communication is now only used in exceptional cases. All IO-Link channels can also be operated in SIO mode and thus used as digital inputs or outputs. The module is also equipped with 8 additional digital inputs that can be used independently of the configuration of the IO-Link channels.
Specification
| I/O module |
IO-Link master with 8 IO-Link interfaces |
|---|---|
| Interfaces |
1x X2X Link / X2X+ |
| B&R ID code |
0x30AE |
| Status indicators |
IO-Link, operating state, module status |
| Module run/error |
Yes, using LED status indicator and software |
| IO-Link operating state |
Yes, using LED status indicator and software |
| C/Q status |
Yes, using LED status indicator and software |
| Cable type |
4-pin standard sensor cable, unshielded |
| Cable length |
Max. 20 m |
| Line capacitance |
Max. 3 nF |
| Loop resistance |
Max. 6 Ω |
| Bus |
0.6 W |
| Internal I/O |
1 W |
| Additional power dissipation caused by actuators (resistive) [W] |
– |
| CE |
Yes |
| UKCA |
Yes |
| CRA (Cyber Resilience Act) |
In preparation |
| Voltage |
I/O power supply minus voltage drop for short-circuit protection |
| Voltage drop for short-circuit protection at 0.5 A |
Max. 0.3 V |
| Power consumption |
Max. 12 W per IO-Link interface |
| Short-circuit proof |
Yes |
| Switch-off delay |
Configurable using software |
| Switch-off duration |
Configurable using software |
| COM1 |
4.8 kbaud |
| COM2 |
38.4 kbaud |
| COM3 |
230.4 kbaud |
| Max. connection capacity |
22 nF (cable + IO-Link device) |
| Max. load |
96 Ω / 250 mA |
| Data format |
1 start bit, 8 data bits, 1 parity bit (even), 1 stop bit |
| Bus level |
24 VDC (active), 0 VDC (resting voltage) |
| Variant |
Bipolar, positive and negative switching |
| Peak short-circuit current |
<1.3 A |
| Residual voltage |
<0.7 VDC at nominal current 0.25 A |
| Switching voltage |
I/O power supply minus voltage drop for short-circuit protection and semiconductor switch |
| Voltage drop on semiconductor switch |
Max. 0.5 VDC at 0.25 A |
| Switching frequency |
Typ. 25 kHz |
| 0 → 1 |
<10 µs |
| 1 → 0 |
<10 µs |
| Switch-on in the event of overload shutdown or short-circuit shutdown |
Configurable with software |
| Insulation voltage between IO-Link and bus |
860 Veff |
| Nominal voltage |
24 VDC |
| Nominal output current |
0.25 A |
| Total nominal current |
Max. 2 A |
| Output circuit |
Sink or source |
| Switching frequency (resistive load) |
Max. 500 Hz |
| Output protection |
Thermal shutdown in the event of overcurrent or short circuit, integrated protection for switching inductive loads |
| Input characteristics per EN 61131-2 |
Type 1 |
| Hardware |
300 ns |
| Software |
– |
| Input circuit |
Sink |
| Input voltage |
24 VDC -15% / +20% |
| Input current at 24 VDC |
Typ. 4 mA |
| Input resistance |
Typ. 6 kΩ |
| Low |
<5 VDC |
| High |
>15 VDC |
| Electrical isolation |
Bus isolated from IO-Link |
| Horizontal |
Yes |
| Vertical |
Yes |
| 0 to 2000 m |
No limitation |
| >2000 m |
Reduction of ambient temperature by 0.5°C per 100 m |
| Maximum |
4000 m |
| Degree of protection per EN 60529 |
IP20 |
| Horizontal mounting orientation |
-25 to 60°C |
| Vertical mounting orientation |
-25 to 50°C |
| Derating |
– |
| Storage |
5 to 95%, non-condensing |
| Transport |
5 to 95%, non-condensing |
| Operation |
5 to 95%, non-condensing |
| Note |
Order terminal blocks separately (see section "Order data"). |
| Width (pitch) |
27.5 +0.2 mm |
| Height |
124 mm |
| Depth |
92 mm |
Reviews
Clear filtersThere are no reviews yet.