Fast delivery within 72 Hours
B&R 8EI8X8MWS10.A600-1
ACOPOS P3 servo drive, 1 digital multi-standard encoder interface per axis, 3x 200-230 VAC, 1x 110-230 VAC, 8.8 A, 1 axis, wall mounting, 8EAC0122.001-1, 1-row connector set, integrated braking resist…
Shipping & Delivery
-
Courier delivery
Our courier will deliver to the specified address
2-3 Days
From $20
-
DHL Courier delivery
DHL courier will deliver to the specified address
2-3 Days
From $40
-
Warranty 1 year
-
Free 30-Day returns
Description
ACOPOS P3 servo drive, 1 digital multi-standard encoder interface per axis, 3x 200-230 VAC, 1x 110-230 VAC, 8.8 A, 1 axis, wall mounting, 8EAC0122.001-1, 1-row connector set, integrated braking resistor
Specification
| Dynamic node allocation (DNA) |
Yes |
|---|---|
| Slots for plug-in modules |
1 |
| Network configurations |
TN-S, TN-C-S with grounded neutral |
| Mains input voltage |
1x 110 VAC to 230 VAC ±10%3x 200 VAC to 230 VAC ±10% |
| Frequency |
50 / 60 Hz ±4% |
| Installed load |
Max. 5 kVA |
| Inrush current |
Max. 22 A |
| Switch-on interval |
Typ. 60 s |
| Integrated line filter per EN 61800-3, category C3 |
No |
| Power dissipation at device nominal power without braking resistor |
[(30 + 10 * PAVG [kW] + 5.8 * IAX1 [A] + 0.25 * IBR12 [A]) + PVSLOT) * 1.1] [W] |
| DC bus capacitance |
1880 µF |
| Input voltage |
24 VDC ±25% |
| Input capacitance |
4312 µF |
| Current consumption |
0.9 A + Current for motor holding brake |
| Quantity |
1 |
| Continuous power per motor connection |
2 kW |
| Continuous current per motor connection |
8.8 Aeff |
| Switching frequency 5 kHz |
75 m |
| Switching frequency 10 kHz |
37.5 m |
| Switching frequency 20 kHz |
18.75 m |
| Starting at 500 m above sea level |
0.88 Aeff per 1000 m |
| Peak current per motor connection |
24 Aeff |
| Peak power output |
5 kW |
| Nominal switching frequency |
5 kHz |
| Possible switching frequencies |
5 / 10 / 20 kHz |
| Insulation stress of the connected motor per IEC TS 60034-25:2004 |
Limit value curve A |
| Overload protection |
Yes |
| Short-circuit and ground fault protection |
Yes |
| Max. output frequency |
598 Hz |
| U, V, W, PE |
Connector |
| Shield connection |
Yes |
| With wire end sleeve |
1.5 to 6 mm² |
| UL/C-UL-US |
24 to 8 AWG |
| CSA |
24 to 8 AWG |
| Output voltage |
Typ. 11.4 V |
| Continuous current per connection |
1.3 A |
| Max. internal resistance |
0.25 Ω |
| Extinction potential |
Approx. 30 V |
| Max. extinction energy per switching operation |
1.5 Ws |
| Max. switching frequency |
0.5 Hz |
| Overload and short-circuit protection |
Yes |
| Open-circuit monitoring |
Yes |
| Undervoltage monitoring |
Yes |
| Response threshold for open-circuit monitoring |
Approx. 30 mA |
| Peak power int./ext. |
1.5 kW / 11 kW |
| Continuous power int./ext. |
100 W / 970 W |
| Minimum braking resistance (ext.) |
12 Ω |
| Circuit |
Sink |
| Input - ACOPOS P3 |
Yes |
| Input - Input |
Yes |
| Nominal |
5 to 40°C |
| Maximum |
55°C |
| Input current at nominal voltage |
Approx. 4 mA |
| Low |
<5 V |
| High |
>15 V |
| Enable 1 → 0, PWM off |
2 ms |
| Enable 0 → 1, ready for PWM |
0.3 ms |
| Modulation compared to ground potential |
Max. ±38 V |
| OSSD signal connections |
0.5 ms |
| Type |
EnDat 2.2 |
| Connections |
8-pin female Mini I/O connector |
| Status indicators |
None |
| Encoder - ACOPOS P3 |
No |
| Encoder monitoring |
No |
| Max. encoder cable length |
100 m Depends on the cross section of the power supply wires in the encoder cable |
| Load capacity |
300 mA |
| Short-circuit proof |
Yes |
| Overload-proof |
Yes |
| Signal transmission |
RS485 |
| Data transfer rate |
6.25 Mbit/s |
| Max. power consumption per encoder interface |
PENCODER [W] = U24V [V] * (IENCODER [A] * 0.7) + 0.5 W |
| Rising edge |
<2 µs |
| Falling edge |
<1 µs |
| Resistance range |
500 Ω to 5 kΩ |
| ACP10 |
V3.13.0 |
| Hanging vertically |
Yes |
| Standing horizontally |
In preparation |
| Pollution degree per EN 61800-5-1 |
2 (non-conductive pollution) |
| Overvoltage category per EN 61800-5-1 |
III |
| Degree of protection per EN 60529 |
IP20 |
| Storage |
5 to 95% |
| Transport |
95% at 40°C |
| Operation |
5 to 85%, non-condensing |
| Width |
66 mm |
| Height |
290 mm |
| Wall mounting |
258.5 mm (with 8EXA front cover: 261 mm) |
| Weight |
3.2 kg |
Reviews
Clear filtersThere are no reviews yet.