Fast delivery within 72 Hours
B&R 8EI2X2HWT10.0600-1
ACOPOS P3 servo drive, 1 digital multi-standard encoder interface per axis, 3x 200-480 VAC, 2.2 A, 3 axes, wall mounting, 1-row connector set, cover, integrated braking resistor
Request for Quote
Shipping & Delivery
-
Courier delivery
Our courier will deliver to the specified address
5-6 Days
From €20
-
DHL Courier delivery
DHL courier will deliver to the specified address
2-3 Days
From €40
-
Warranty 1 year
-
Free 30-Day returns
Description
ACOPOS P3 servo drive, 1 digital multi-standard encoder interface per axis, 3x 200-480 VAC, 2.2 A, 3 axes, wall mounting, 1-row connector set, cover, integrated braking resistor
Specification
| Dynamic node allocation (DNA) | Yes |
|---|---|
| Slots for plug-in modules | 1 |
| Network configurations | TN-S, TN-C-S with grounded neutral |
| Mains input voltage | 3x 200 VAC to 480 VAC ±10% |
| Frequency | 50 / 60 Hz ±4% |
| Installed load | Max. 7.5 kVA |
| Inrush current | Max. 45 A |
| Switch-on interval | Typ. 60 s |
| Integrated line filter per EN 61800-3, category C3 | No |
| Power dissipation at device nominal power without braking resistor | [(60 + 6.9 * PAVG [kW] + 7.5 * (IAX1 [A] + IAX2 [A] + IAX3 [A]) + 0.25 * (IBR12 [A] + IBR22 [A] + IBR32 [A]) + PVSLOT) * 1.1] [W] |
| DC bus capacitance | 470 µF |
| Input voltage | 24 VDC ±25% |
| Input capacitance | 5507 µF |
| Current consumption | 1.2 A + Current for motor holding brake |
| Quantity | 3 |
| Continuous power per motor connection | 1 / 1 / 1 kW |
| Continuous current per motor connection | 2.2 / 2.2 / 2.2 Aeff |
| Switching frequency 5 kHz | 75 m |
| Switching frequency 10 kHz | 37.5 m |
| Switching frequency 20 kHz | 18.75 m |
| Starting at 500 m above sea level | 0.22 Aeff per 1000 m |
| Peak current per motor connection | 6 / 6 / 6 Aeff |
| Peak power output | 2.5 kW |
| Nominal switching frequency | 5 kHz |
| Possible switching frequencies | 5 / 10 / 20 kHz |
| Insulation stress of the connected motor per IEC TS 60034-25:2004 | Limit value curve A |
| Overload protection | Yes |
| Short-circuit and ground fault protection | Yes |
| Max. output frequency | 598 Hz |
| U, V, W, PE | Connector |
| Shield connection | Yes |
| With wire end sleeve | 1.5 to 6 mm² |
| UL/C-UL-US | 24 to 8 AWG |
| CSA | 24 to 8 AWG |
| Output voltage | Typ. 11.4 V |
| Continuous current per connection | 1.3 A |
| Max. internal resistance | 0.25 Ω |
| Extinction potential | Approx. 30 V |
| Max. extinction energy per switching operation | 1.5 Ws |
| Max. switching frequency | 0.5 Hz |
| Overload and short-circuit protection | Yes |
| Open-circuit monitoring | Yes |
| Undervoltage monitoring | Yes |
| Response threshold for open-circuit monitoring | Approx. 30 mA |
| Peak power int./ext. | 7 kW / 25 kW |
| Continuous power int./ext. | 150 W / 2 kW |
| Minimum braking resistance (ext.) | 25 Ω |
| Circuit | Sink |
| Input - ACOPOS P3 | Yes |
| Input - Input | Yes |
| Nominal | 5 to 40°C |
| Maximum | 55°C |
| Input current at nominal voltage | Approx. 4 mA |
| Low | <5 V |
| High | >15 V |
| Enable 1 → 0, PWM off | 2 ms |
| Enable 0 → 1, ready for PWM | 0.3 ms |
| Modulation compared to ground potential | Max. ±38 V |
| OSSD signal connections | 0.5 ms |
| Type | EnDat 2.2 |
| Connections | 8-pin female Mini I/O connector |
| Status indicators | None |
| Encoder - ACOPOS P3 | No |
| Encoder monitoring | No |
| Max. encoder cable length | 100 m Depends on the cross section of the power supply wires in the encoder cable |
| Load capacity | 300 mA |
| Short-circuit proof | Yes |
| Overload-proof | Yes |
| Signal transmission | RS485 |
| Data transfer rate | 6.25 Mbit/s |
| Max. power consumption per encoder interface | PENCODER [W] = U24V [V] * (IENCODER [A] * 0.7) + 0.5 W |
| Rising edge | <2 µs |
| Falling edge | <1 µs |
| Resistance range | 500 Ω to 5 kΩ |
| ACP10 | V3.12.1 |
| Hanging vertically | Yes |
| Standing horizontally | In preparation |
| Pollution degree per EN 61800-5-1 | 2 (non-conductive pollution) |
| Overvoltage category per EN 61800-5-1 | III |
| Degree of protection per EN 60529 | IP20 |
| Storage | 5 to 95% |
| Transport | 95% at 40°C |
| Operation | 5 to 85%, non-condensing |
| Width | 66 mm |
| Height | 374 mm |
| Wall mounting | 258.5 mm (with 8EXA front cover: 261 mm) |
| Weight | 4 kg |
Reviews
Clear filtersThere are no reviews yet.