Fast delivery within 72 Hours
B&R 8EI017HWS10.XXXX-1
ACOPOS P3 servo drive, 1 digital multi-standard encoder interface per axis, 3x 200-480 VAC, 17 A, 1 axis, wall mounting
Request for Quote
Shipping & Delivery
-
Courier delivery
Our courier will deliver to the specified address
5-6 Days
From €20
-
DHL Courier delivery
DHL courier will deliver to the specified address
2-3 Days
From €40
-
Warranty 1 year
-
Free 30-Day returns
Description
ACOPOS P3 servo drive, 1 digital multi-standard encoder interface per axis, 3x 200-480 VAC, 17 A, 1 axis, wall mounting
Specification
| Dynamic node allocation (DNA) | Yes |
|---|---|
| Slots for plug-in modules | 1 |
| CE | Yes |
| UKCA | Yes |
| CRA (Cyber Resilience Act) | In preparation |
| UL | cULus E225616 Power conversion equipment |
| Network configurations | TT, TN, TN-S, TN-C-S, IT |
| Mains input voltage | 3x 200 VAC to 480 VAC ±10% |
| Frequency | 50 / 60 Hz ±4% |
| Installed load | Max. 18 kVA |
| Inrush current | Max. 50 A |
| Switch-on interval | Typically 60 s |
| Integrated line filter per EN 61800-3, category C3 | No |
| With wire end sleeve | 0.25 to 2.5 mm² |
| UL/C-UL-US | 26 to 12 AWG |
| CSA | 26 to 12 AWG |
| Power dissipation at device nominal power without braking resistor | [37 W + 9.2 V * IAX1 + 6.3 W/kW * PAVG + 0.25 Ω * IBR12 + PVSLOT] * 1.1 |
| Max. line length | 100 m |
| Continuous power | 8.5 kW |
| Mains input voltage <3x 400 VAC | 8.5 kW * (Mains input voltage [V] / 400 V) |
| DC bus capacitance | 940 µF |
| With wire end sleeves | 0.25 to 4 mm² |
| Input voltage | 24 VDC ±25% |
| Input capacitance | 5500 µF |
| Current consumption | 1.2 A + Current for motor holding brake |
| Quantity | 1 |
| Continuous power per motor connection | 8.5 kW |
| Continuous current per motor connection | 17 Aeff |
| Switching frequency 5 kHz | 75 m |
| Switching frequency 10 kHz | 38 m |
| Switching frequency 20 kHz | 19 m |
| Starting at 500 m above sea level | 1.7 Aeff per 1000 m |
| Peak current per motor connection | 42.5 Aeff |
| Peak power output | 21.25 kW |
| Nominal switching frequency | 5 kHz |
| Possible switching frequencies | 2.5 / 5 / 10 / 20 kHz |
| Insulation stress of the connected motor per IEC TS 60034-25:2004 | Limit value curve A |
| Overload protection | No |
| Short-circuit and ground fault protection | Short-circuit protection: Yes Ground fault protection: No |
| Max. output frequency | 598 Hz |
| U, V, W, PE | Connector |
| Shield connection | Yes Clamping range of the grounding clamp: 17 to 30 mm |
| Output voltage | Configurable Typ. 11.45 V ±0.1 V / 5.2 V ±0.1 V |
| Continuous current per connection | 4 A |
| Max. internal resistance | 100 mΩ |
| Extinction potential | 33 V |
| Max. extinction energy per switching operation | 15 Ws |
| Max. switching frequency | 0.5 Hz |
| Overload and short-circuit protection | Yes |
| Open-circuit monitoring | Yes |
| Undervoltage monitoring | Yes |
| Response threshold for open-circuit monitoring | Max. 70 mA |
| Response threshold for undervoltage monitoring | Approx. 23 V |
| Peak power int./ext. | 14 kW / 25 kW |
| Continuous power int./ext. | 150 W / 4 kW |
| Minimum braking resistance (ext.) | 25 Ω |
| Type | Digital multi-encoder interface, configurable |
| Variant | 2x RJ45, shielded, 2-port hub |
| Line length | Max. 100 m between 2 stations (segment length) |
| Transfer rate | 100 Mbit/s |
| Circuit | Sink |
| Input - ACOPOS P3 | Yes |
| Input - Input | Yes |
| Nominal | 5 to 40°C |
| Maximum | 55°C |
| Input current at nominal voltage | 7 mA |
| Low | <5 V |
| High | >15 V |
| Enable 1 → 0, PWM off | 2 ms |
| Enable 0 → 1, ready for PWM | 0.3 ms ACP10 5.16.2 and later: 4.3 ms |
| Modulation compared to ground potential | Max. ±38 V |
| OSSD signal connections | 0.5 ms |
| With plastic wire end sleeves | 0.25 to 2.5 mm² |
| Connections | 8-pin female Mini I/O connector |
| Status indicators | None |
| Encoder - ACOPOS P3 | No |
| Max. encoder cable length | 75 m Depends on the cross section of the power supply wires in the encoder cable |
| Load capacity | Max. 300 mA |
| Sense lines | 2, compensation of max. 2x 0.7 V |
| Short-circuit proof | Yes |
| Overload-proof | Yes |
| Signal transmission | RS485 |
| Data transfer rate | Depends on the configured encoder type |
| Minimum | -25°C |
| Max. power consumption per encoder interface | PENCODER [W] = U24V [V] * (IENCODER [A] * 0.7) + 0.5 W |
| Rising edge | <51 µs |
| Falling edge | <52 µs |
| Resistance range | 500 Ω to 5 kΩ |
| Mapp Motion | 5.03.0 and higher |
| ACP10/ARNC0 | 3.17.0 and higher |
| Power dissipation relative to continuous apparent power | IE2 (10,25) 1% IE2 (50,25) 1% IE2 (10,50) 1.2% IE2 (50,50) 1.3% IE2 (90,50) 1.4% IE2 (10,100) 1.7% IE2 (50,100) 1.9% IE2 (90,100) 2.2% |
| Nominal losses in standby mode | 11.8 W |
| Hanging vertically | Yes |
| Standing horizontally | Yes |
| Pollution degree per EN 61800-5-1 | 2 (non-conductive pollution) |
| Overvoltage category per EN 61800-5-1 | III |
| Degree of protection per EN 60529 | IP20 |
| Storage | 5 to 95% |
| Transport | 95% at 40°C |
| Operation | 5 to 85%, non-condensing |
| Width | 66 mm |
| Height | 374 mm |
| Wall mounting | 258.5 mm (with 8EXA front cover: 261 mm) |
| Weight | 4 kg |
Reviews
Clear filtersThere are no reviews yet.