Intrinsic Safety Barriers Archives - CentralXL | Industrial Marketplace

Pepperl Fuchs KFU8-UFC-Ex1.D

sales@partnerplc.com — Tue, 20 Jan 2026 13:29:53 +0000

Frequency Converter with Trip Values. 1-channel isolated barrier, Universal usage at different power supplies, Input for NAMUR sensors or dry contacts, Input frequency 1 mHz … 5 kHz, Current output 0/4 mA … 20 mA, Relay contact and transistor output, Start-up override, Line fault detection (LFD), Up to SIL 2 acc. to IEC/EN 61508 / IEC/EN 61511, Housing width: 40 mm, Number of channels: 1-channel, Trip relay, Start-up override, Frequency conversion, Rotation speed monitoring, Pulse divider. Signal type: Digital Input. Safety Integrity Level (SIL): SIL 2. Connection: terminals 23, 24. Rated voltage: 20 … 90 V DC / 48 … 253 V AC 50 … 60 Hz. Power dissipation/power consumption: ≤ 2 W ; 2.5 VA / 2.2 W ; 3 VA. Programming interface: programming socket. Connection side: field side. Connection: Input I: intrinsically safe: terminals 1+, 3- Input II: non-intrinsically safe: terminals 13+, 14-. Input I: sensor acc. to EN 60947-5-6 (NAMUR) or mechanical contact. Pulse duration> 50 µsInput frequency0.001 … 5000 HzLine fault detectionbreakage I ≤ 0.15 mA; short-circuit I > 6.5 mA: . Pulse duration: > 50 µs. Input frequency: 0.001 … 5000 Hz. Line fault detection: breakage I ≤ 0.15 mA; short-circuit I > 6.5 mA. Input II: startup override: 1 … 1000 s, adjustable in steps of 1 s. Active/PassiveI > 4 mA (for min. 100 ms) / I 4 mA (for min. 100 ms) / I 0.001 HzMeasuring time 0.001 Hz. Measuring time: < 100 ms. Influence of ambient temperature: 0.003 %/K (30 ppm). Output I, II: . Response delay≤ 200 ms: . Response delay: ≤ 200 ms. Output IV: . Resolution< 10 µAAccuracy< 20 µAInfluence of ambient temperature0.005 %/K (50 ppm): . Resolution: < 10 µA. Accuracy: 0.7; 40 V DC/2 A resistive load (TÜV 99 ATEX 1471): Um. Maximum safe voltage: 253 V (Attention! The rated voltage can be lower.). Contact loading: 253 V AC/2 A/cos φ > 0.7; 40 V DC/2 A resistive load (TÜV 99 ATEX 1471). Output III: terminals 19+, 20- non-intrinsically safe. Maximum safe voltage UmUm40 V (Attention! Um is no rated voltage.): Um. Maximum safe voltage Um: 40 V (Attention! Um is no rated voltage.). Output IV: terminals 8+, 7- non-intrinsically safe. Maximum safe voltageUm40 V DC (Attention! Um is no rated voltage.): Um. Maximum safe voltage: 40 V DC (Attention! Um is no rated voltage.). Interface: RS 232. Maximum safe voltageUm40 V (Attention! Um is no rated voltage.): Um. Maximum safe voltage: 40 V (Attention! Um is no rated voltage.). Galvanic isolation: . Input I/other circuitssafe electrical isolation acc. to IEC/EN 60079-11, voltage peak value 375 V: . Input I/other circuits: safe electrical isolation acc. to IEC/EN 60079-11, voltage peak value 375 V. Directive conformity: . Directive 2014/34/EUEN IEC 60079-0:2018 , EN 60079-11:2012: . Directive 2014/34/EU: EN IEC 60079-0:2018 , EN 60079-11:2012. FM approval: . Control drawing16-538FM-12: . Control drawing: 16-538FM-12. IECEx approval: . IECEx certificateIECEx TUN 04.0007IECEx marking[Ex ia Ga] IIC , [Ex ia Da] IIIC , [Ex ia Ma] I: . IECEx certificate: IECEx TUN 04.0007. IECEx marking: [Ex ia Ga] IIC , [Ex ia Da] IIIC , [Ex ia Ma] I. Supplementary information: Observe the certificates, declarations of conformity, instruction manuals, and manuals where applicable. For information see www.pepperl-fuchs.com.

The post Pepperl Fuchs KFU8-UFC-Ex1.D appeared first on CentralXL | Industrial Marketplace.

Pepperl Fuchs KFD2-VR-Ex1.19

sales@partnerplc.com — Tue, 20 Jan 2026 13:29:50 +0000

Voltage Repeater. 1-channel isolated barrier, 24 V DC supply (Power Rail), Voltage input -10 V … 10 V, Voltage output -10 V … 10 V, Housing width: 20 mm, Number of channels: 1-channel, Transfer direction: to the control system, Rated voltage: 20 … 35 V DC, Signal: 1 x -10 … 10 V, Signal: 1 x -10 … 10 V, Cut-off frequency: 1.2 kHz (-3 dB). Signal type: Analog input. Connection: Power Rail or terminals 11+, 12-. Rated voltage: 20 … 35 V DC. Ripple: within the supply tolerance. Rated current: < 25 mA. Connection side: field side. Connection: terminals 4+, 5-. Input resistance: min. 10 MΩ. Transmission range: -10 … 10 V. Offset voltage/current: < 2 mV / < 7 nA. Connection side: control side. Connection: terminals 7-, 8+. Voltage: -10 … 10 V. Output resistance: max. 20 Ω. Cut-off frequency: 1.2 kHz (-3 dB). Deviation: . After calibration± 5 mV at 20 °C (68 °F)Influence of ambient temperature< 0.005 % of range per K: . After calibration: ± 5 mV at 20 °C (68 °F). Influence of ambient temperature: < 0.005 % of range per K. Rise time: ≤ 0.4 ms. Output/power supply: functional insulation, rated insulation voltage 50 V AC. Display elements: LED. Labeling: space for labeling at the front. Electromagnetic compatibility: . Directive 2014/30/EUEN 61326-1:2013 (industrial locations): . Directive 2014/30/EU: EN 61326-1:2013 (industrial locations). Electromagnetic compatibility: NE 21. Degree of protection: IEC 60529. Ambient temperature: -20 … 60 °C (-4 … 140 °F). Degree of protection: IP20. Connection: screw terminals. Mass: approx. 100 g. Dimensions: 20 x 107 x 115 mm (0.8 x 4.2 x 4.5 inch) (W x H x D) , housing type B1. Height100 mmWidth20 mmDepth115 mm: . Height: 100 mm. Width: 20 mm. Depth: 115 mm. Mounting: on 35 mm DIN mounting rail acc. to EN 60715:2001. EU-type examination certificate: BAS 01 ATEX 7262. Marking II (1)GD, I (M1) [Ex ia Ga] IIC, [Ex ia Da] IIIC, [Ex ia Ma] I (-20 °C ≤ Tamb ≤ 60 °C) , [circuit(s) in zone 0/1/2]VoltageUo18 VCurrentIo4.2 mAPowerPo19 mW: . Marking: II (1)GD, I (M1) [Ex ia Ga] IIC, [Ex ia Da] IIIC, [Ex ia Ma] I (-20 °C ≤ Tamb ≤ 60 °C) , [circuit(s) in zone 0/1/2]. Voltage: 18 V. Current: 4.2 mA. Power: 19 mW. Supply: . Maximum safe voltageUm250 V (Attention! The rated voltage is lower.): Um. Maximum safe voltage: 250 V (Attention! The rated voltage is lower.). Output: . Maximum safe voltageUm250 V (Attention! The rated voltage is lower.): Um. Maximum safe voltage: 250 V (Attention! The rated voltage is lower.). Certificate: BASEEFA 10 ATEX 0079X. Marking II 3G Ex ec IIC T4 Gc [device in zone 2]: . Marking: II 3G Ex ec IIC T4 Gc [device in zone 2]. Galvanic isolation: . Input/Outputsafe electrical isolation acc. to IEC/EN 60079-11, voltage peak value 375 VInput/power supplysafe electrical isolation acc. to IEC/EN 60079-11, voltage peak value 375 V: . Input/Output: safe electrical isolation acc. to IEC/EN 60079-11, voltage peak value 375 V. Input/power supply: safe electrical isolation acc. to IEC/EN 60079-11, voltage peak value 375 V. Directive conformity: . Directive 2014/34/EUEN 60079-0:2012+A11:2013 , EN 60079-11:2012 , EN 60079-7:2015+A1:2018: . Directive 2014/34/EU: EN 60079-0:2012+A11:2013 , EN 60079-11:2012 , EN 60079-7:2015+A1:2018. FM approval: . Control drawing116-0129: . Control drawing: 116-0129. UL approval: . Control drawing116-0173 (cULus): . Control drawing: 116-0173 (cULus). CSA approval: . Control drawing116-0132: . Control drawing: 116-0132. IECEx approval: . IECEx certificateIECEx BAS 10.0040XIECEx markingEx ec IIC T4 Gc: . IECEx certificate: IECEx BAS 10.0040X. IECEx marking: Ex ec IIC T4 Gc. Supplementary information: Observe the certificates, declarations of conformity, instruction manuals, and manuals where applicable. For information see www.pepperl-fuchs.com.

The post Pepperl Fuchs KFD2-VR-Ex1.19 appeared first on CentralXL | Industrial Marketplace.

Pepperl Fuchs KFD2-UT2-Ex2

sales@partnerplc.com — Tue, 20 Jan 2026 13:29:49 +0000

Universal Temperature Converter. 2-channel isolated barrier, 24 V DC supply (Power Rail), Thermocouple, RTD, potentiometer or voltage input, Usable as signal splitter (1 input and 2 outputs), Current output 0/4 mA … 20 mA, Sink or source mode, Configurable by PACTware, Line fault (LFD) and sensor burnout detection, Up to SIL 2 acc. to IEC/EN 61508 / IEC/EN 61511, Housing width: 20 mm, Number of channels: 2-channel, Safety Integrity Level (SIL): SIL 2, Rated voltage: 20 … 30 V DC, Type: 2-wire connection. Signal type: Analog input. Safety Integrity Level (SIL): SIL 2. Connection: terminals 14+, 15- or power feed module/Power Rail. Rated voltage: 20 … 30 V DC. Ripple: within the supply tolerance. Power dissipation: ≤ 1.53 W. Power consumption: max. 1.53 W. Programming interface: programming socket. Connection side: field side. Connection: terminals 1, 2, 3; 4, 5, 6. RTD: type Pt10, Pt50, Pt100, Pt500, Pt1000 (EN 60751: 1995)type Pt10GOST, Pt50GOST, Pt100GOST, Pt500GOST, Pt1000GOST (6651-94)type Cu10, Cu50, Cu100 (P50353-92)type Ni100 (DIN 43760). Measuring currentapprox. 200 µA with RTDTypes of measuring2-, 3-wire connectionLead resistancemax. 50 Ω per lineMeasurement loop monitoringsensor breakage, sensor short-circuit: . Measuring current: approx. 200 µA with RTD. Types of measuring: 2-, 3-wire connection. Lead resistance: max. 50 Ω per line. Measurement loop monitoring: sensor breakage, sensor short-circuit. Thermocouples: type B, E, J, K, N, R, S, T (IEC 584-1: 1995)type L (DIN 43710: 1985)type TXK, TXKH, TXA (P8.585-2001). Cold junction compensationexternal and internalMeasurement loop monitoringsensor breakage: . Cold junction compensation: external and internal. Measurement loop monitoring: sensor breakage. Potentiometer: 0 … 20 kΩ (2-wire connection), 0.8 … 20 kΩ (3-wire connection). Voltage: selectable within the range -100 … 100 mV. Input resistance: ≥ 1 MΩ (-100 … 100 mV). Connection side: control side. Connection: output I: terminal 7: source (-), sink (+), terminal 8: source (+), terminal 9: sink(-) output II: terminal 10: source (-), sink (+), terminal 11: source (+), terminal 12: sink(-). Output I, II: Analog current output. Current range0 … 20 mA or 4 … 20 mAFault signaldownscale 0 or 2 mA, upscale 21.5 mA (acc. NAMUR NE43)Sourceload 0 … 550 Ω open-circuit voltage ≤ 18 VSinkVoltage across terminals 5 … 30 V. If the current is supplied from a source > 16.5 V,series resistance of ≥ (V – 16.5)/0.0215 Ω is needed, where V is the source voltage.The maximum value of the resistance is (V – 5)/0.0215 Ω.: . Current range: 0 … 20 mA or 4 … 20 mA. Fault signal: downscale 0 or 2 mA, upscale 21.5 mA (acc. NAMUR NE43). Source: load 0 … 550 Ω open-circuit voltage ≤ 18 V. Sink: Voltage across terminals 5 … 30 V. If the current is supplied from a source > 16.5 V,series resistance of ≥ (V – 16.5)/0.0215 Ω is needed, where V is the source voltage.The maximum value of the resistance is (V – 5)/0.0215 Ω.. Deviation: . After calibrationPt100: ± (0.06 % of measurement value in K + 0.1 % of span + 0.1 K (4-wire connection)) thermocouple: ± (0.05 % of measurement value in °C + 0.1 % of span + 1 K (1.2 K for types R and S)) , includes ± 0.8 K fault of the cold junction compensation (CJC) mV: ± (50 µV + 0.1 % of span)potentiometer: ± (0.05 % of full scale + 0.1 % of span, (excludes faults due to lead resistance))Influence of ambient temperaturePt100: ± (0.0015 % of measurement value in K + 0.006 % of span)/K ΔTamb*)thermocouple: ± (0.02 K + 0.005 % of measurement value in °C + 0.006 % of span)/K ΔTamb*)), influence of cold junction compensation (CJC) includedmV: ± (0.01 % of measurement value + 0.006 % of span)/K ΔTamb*)potentiometer: ± 0.006 % of span/K ΔTamb*) *) ΔTamb = ambient temperature change referenced to 23 °C (296 K)Influence of supply voltage< 0.01 % of spanInfluence of load≤ 0.001 % of output value per 100 Ω: . After calibration: Pt100: ± (0.06 % of measurement value in K + 0.1 % of span + 0.1 K (4-wire connection)) thermocouple: ± (0.05 % of measurement value in °C + 0.1 % of span + 1 K (1.2 K for types R and S)) , includes ± 0.8 K fault of the cold junction compensation (CJC) mV: ± (50 µV + 0.1 % of span)potentiometer: ± (0.05 % of full scale + 0.1 % of span, (excludes faults due to lead resistance)). Influence of ambient temperature: Pt100: ± (0.0015 % of measurement value in K + 0.006 % of span)/K ΔTamb*)thermocouple: ± (0.02 K + 0.005 % of measurement value in °C + 0.006 % of span)/K ΔTamb*)), influence of cold junction compensation (CJC) includedmV: ± (0.01 % of measurement value + 0.006 % of span)/K ΔTamb*)potentiometer: ± 0.006 % of span/K ΔTamb*) *) ΔTamb = ambient temperature change referenced to 23 °C (296 K). Influence of supply voltage: < 0.01 % of span. Influence of load: ≤ 0.001 % of output value per 100 Ω. Reaction time: worst case value (sensor breakage and/or sensor short circuit detection enabled)mV: 1.2 s, thermocouples with CJC: 1.4 s, thermocouples with fixed ref. temp: 1.4 s, 3- or 4-wire RTD: 1.1 s, 2-wire RTD: 920 ms, Potentiometer: 3-wire connection 2.8 s, 2-wire connection 2.25 s. Output/supply, programming input: functional insulation, rated insulation voltage 50 V AC There is no electrical isolation between the programming input and the supply.The programming cable provides galvanic isolation so that ground loops are avoided.. Display elements: LEDs. Configuration: via PACTware. Labeling: space for labeling at the front. Electromagnetic compatibility: . Directive 2014/30/EUEN 61326-1:2013 (industrial locations): . Directive 2014/30/EU: EN 61326-1:2013 (industrial locations). Electromagnetic compatibility: NE 21:2006. Degree of protection: IEC 60529:2001. Protection against electrical shock: UL 61010-1:2004. Ambient temperature: -20 … 60 °C (-4 … 140 °F). Degree of protection: IP20. Connection: screw terminals. Mass: approx. 130 g. Dimensions: 20 x 119 x 115 mm (0.8 x 4.7 x 4.5 inch) (W x H x D) , housing type B2. Height119 mmWidth20 mmDepth115 mm: . Height: 119 mm. Width: 20 mm. Depth: 115 mm. Mounting: on 35 mm DIN mounting rail acc. to EN 60715:2001. EU-type examination certificate: CESI 04 ATEX 143. Marking II (1)G [Ex ia Ga] IIC [exsign] II (1)D [Ex ia Da] IIIC [exsign] I (M1) [Ex ia Ma] IInputEx ia: . Marking: II (1)G [Ex ia Ga] IIC [exsign] II (1)D [Ex ia Da] IIIC [exsign] I (M1) [Ex ia Ma] I. Input: Ex ia. Inputs: terminals 1, 2, 3, 4, 5, 6 (for passive equipment). Voltage Uo9 VCurrent Io22 mAPower Po50 mW: . Voltage Uo: 9 V. Current Io: 22 mA. Power Po: 50 mW. Analog outputs, power supply, collective error: . Maximum safe voltageUm250 V (Attention! This is not the rated voltage.): Um. Maximum safe voltage: 250 V (Attention! This is not the rated voltage.). Interface: . Maximum safe voltageUm250 V (Attention! The rated voltage is lower.), RS 232: Um. Maximum safe voltage: 250 V (Attention! The rated voltage is lower.), RS 232. Certificate: TÜV 02 ATEX 1797 X. Marking II 3G Ex nA II T4: . Marking: II 3G Ex nA II T4. Galvanic isolation: . Input/Other circuitssafe electrical isolation acc. to IEC/EN 60079-11, voltage peak value 375 V: . Input/Other circuits: safe electrical isolation acc. to IEC/EN 60079-11, voltage peak value 375 V. Directive conformity: . Directive 2014/34/EUEN 60079-0:2012+A11:2013 , EN 60079-11:2012 , EN 60079-15:2010 , EN 50303:2000: . Directive 2014/34/EU: EN 60079-0:2012+A11:2013 , EN 60079-11:2012 , EN 60079-15:2010 , EN 50303:2000. UL approval: . Control drawing116-0410: . Control drawing: 116-0410. CSA approval: . Control drawing116-0314 (cCSAus) 116-0347: . Control drawing: 116-0314 (cCSAus) 116-0347. IECEx approval: . IECEx certificateIECEx TUN 07.0003 IECEx CML 16.0126XIECEx marking[Ex ia Ga] IIC [Ex ia Da] IIIC [Ex ia Ma] I Ex nA IIC T4 Gc: . IECEx certificate: IECEx TUN 07.0003 IECEx CML 16.0126X. IECEx marking: [Ex ia Ga] IIC [Ex ia Da] IIIC [Ex ia Ma] I Ex nA IIC T4 Gc. Supplementary information: Observe the certificates, declarations of conformity, instruction manuals, and manuals where applicable. For information see www.pepperl-fuchs.com.

The post Pepperl Fuchs KFD2-UT2-Ex2 appeared first on CentralXL | Industrial Marketplace.

Pepperl Fuchs KFD2-UFC-Ex1.D

sales@partnerplc.com — Tue, 20 Jan 2026 13:29:47 +0000

Frequency Converter with Trip Values. 1-channel isolated barrier, 24 V DC supply (Power Rail), Input for NAMUR sensors or dry contacts, Input frequency 1 mHz … 5 kHz, Current output 0/4 mA … 20 mA, Relay contact and transistor output, Start-up override, Line fault detection (LFD), Up to SIL 2 acc. to IEC/EN 61508 / IEC/EN 61511, Housing width: 40 mm, Number of channels: 1-channel, Trip relay, Start-up override, Frequency conversion, Rotation speed monitoring, Pulse divider, Safety Integrity Level (SIL): SIL 2. Signal type: Digital Input. Safety Integrity Level (SIL): SIL 2. Connection: terminals 23+, 24- or power feed module/Power Rail. Rated voltage: 20 … 30 V DC. Rated current: approx. 100 mA. Power dissipation/power consumption: ≤ 2 W / 2.2 W. Programming interface: programming socket. Connection side: field side. Connection: Input I: intrinsically safe: terminals 1+, 3- Input II: non-intrinsically safe: terminals 13+, 14-. Input I: sensor acc. to EN 60947-5-6 (NAMUR) or mechanical contact. Pulse duration> 50 µsInput frequency0.001 … 5000 HzLine fault detectionbreakage I ≤ 0.15 mA; short-circuit I > 6.5 mA: . Pulse duration: > 50 µs. Input frequency: 0.001 … 5000 Hz. Line fault detection: breakage I ≤ 0.15 mA; short-circuit I > 6.5 mA. Input II: startup override: 1 … 1000 s, adjustable in steps of 1 s. Active/PassiveI > 4 mA (for min. 100 ms) / I 4 mA (for min. 100 ms) / I 0.001 HzMeasuring time 0.001 Hz. Measuring time: < 100 ms. Influence of ambient temperature: 0.003 %/K (30 ppm). Output I, II: . Response delay≤ 200 ms: . Response delay: ≤ 200 ms. Output IV: . Resolution< 10 µAAccuracy< 20 µAInfluence of ambient temperature0.005 %/K (50 ppm): . Resolution: < 10 µA. Accuracy: 0.7; 40 V DC/2 A resistive load: Um. Maximum safe voltage: 253 V (Attention! The rated voltage can be lower.). Contact loading: 253 V AC/2 A/cos φ > 0.7; 40 V DC/2 A resistive load. Output III: terminals 19+, 20- non-intrinsically safe. Maximum safe voltage UmUm40 V (Attention! Um is no rated voltage.): Um. Maximum safe voltage Um: 40 V (Attention! Um is no rated voltage.). Output IV: terminals 8+, 7- non-intrinsically safe. Maximum safe voltageUm40 V DC (Attention! Um is no rated voltage.): Um. Maximum safe voltage: 40 V DC (Attention! Um is no rated voltage.). Interface: RS 232. Maximum safe voltageUm40 V (Attention! Um is no rated voltage.): Um. Maximum safe voltage: 40 V (Attention! Um is no rated voltage.). Certificate: TÜV 02 ATEX 1885 X. Marking II 3G Ex nA nC IIC T4 Gc: . Marking: II 3G Ex nA nC IIC T4 Gc. Output I, II: . Contact loading50 V AC/2 A/cos φ > 0.7; 40 V DC/2 A resistive load: . Contact loading: 50 V AC/2 A/cos φ > 0.7; 40 V DC/2 A resistive load. Galvanic isolation: . Input I/other circuitssafe electrical isolation acc. to IEC/EN 60079-11, voltage peak value 375 V: . Input I/other circuits: safe electrical isolation acc. to IEC/EN 60079-11, voltage peak value 375 V. Directive conformity: . Directive 2014/34/EUEN 60079-0:2012+A11:2013 , EN 60079-11:2012 , EN 60079-15:2010: . Directive 2014/34/EU: EN 60079-0:2012+A11:2013 , EN 60079-11:2012 , EN 60079-15:2010. FM approval: . Control drawing16-538FM-12: . Control drawing: 16-538FM-12. UL approval: E223772. IECEx approval: . IECEx certificateIECEx TUN 04.0007 IECEx TSA 18.0007XIECEx marking[Ex ia Ga] IIC, [Ex ia Da] IIIC, [Ex ia Ma] I Ex ec nC IIC T4 Gc: . IECEx certificate: IECEx TUN 04.0007 IECEx TSA 18.0007X. IECEx marking: [Ex ia Ga] IIC, [Ex ia Da] IIIC, [Ex ia Ma] I Ex ec nC IIC T4 Gc. Supplementary information: Observe the certificates, declarations of conformity, instruction manuals, and manuals where applicable. For information see www.pepperl-fuchs.com.

The post Pepperl Fuchs KFD2-UFC-Ex1.D appeared first on CentralXL | Industrial Marketplace.

Pepperl Fuchs KFD2-STC5-Ex2

sales@partnerplc.com — Tue, 20 Jan 2026 13:29:40 +0000

SMART Transmitter Power Supply. 2-channel isolated barrier, 24 V DC supply (Power Rail), Input 2-wire and 3-wire SMART transmitters and 2-wire SMART current sources, Output 4 mA … 20 mA current sink/current source, Terminals with test points, Up to SIL 2 (SC 3) acc. to IEC/EN 61508, Housing width: 20 mm, Number of channels: 2-channel, HART communication, Test sockets, Safety Integrity Level (SIL): SIL 2, Systematic capability (SC): SC 3, Rated voltage: 18 … 30 V DC, Field device: 2-wire transmitter. Signal type: Analog input. Safety Integrity Level (SIL): SIL 2. Systematic capability (SC): SC 3. Connection: Power Rail or terminals 14+, 15-. Rated voltage: 18 … 30 V DC. Ripple: within the supply tolerance. Power dissipation: ≤ 1.4 W at maximum load. Power consumption: ≤ 2.6 W at maximum load. Connection side: field side. Connection: terminals 1+, 2-, 3; 4+, 5-, 6. Input signal: 4 … 20 mA. Open circuit voltage/short-circuit current: terminals 1+, 3; 4+, 6: 23 V / 25 mA. Input resistance: max. 265 Ω terminals 2-, 3; 5-, 6 , max. 330 Ω terminals 1+, 3; 4+, 6. Available voltage: ≥ 16 V at 20 mA ; ≥ 20 V at 4 mA , terminals 1+, 3; 4+, 6. Connection side: control side. Connection: terminals 7+, 8-, 9-; 10+, 11-, 12- (sink)terminals 7-, 8+, 9+; 10-, 11+, 12+ (source) see additional information. Load: 0 … 600 Ω. Output signal: 4 … 20 mA (overload > 25 mA). Ripple: max. 50 µA rms. External supply (loop): 2 … 30 V DC If the external voltage is > 19 V, a load ≥ ((V – 19) / 0.02) Ω is required. V represents the value of the external voltage. The internal 250 Ω resistor at terminals 9 and 12 can be used as a load.. Deviation: at 20 °C (68 °F), 4 … 20 mA≤ 10 µA incl. calibration, linearity, hysteresis, loads and fluctuations of supply voltage. Influence of ambient temperature≤ 0.25 µA/K: . Influence of ambient temperature: ≤ 0.25 µA/K. Frequency range: field side into the control side: band width with 1 Vpp signal 0 … 7.5 kHz (-3 dB) safe area to hazardous area: band width with 1 VSS signal 0.3 … 7.5 kHz (-3 dB). Settling time: 200 µs. Rise time/fall time: 100 µs. Output/power supply: functional insulation, rated insulation voltage 50 V AC. Output/Output: functional insulation, rated insulation voltage 50 V AC. Display elements: LED. Labeling: space for labeling at the front. Electromagnetic compatibility: . Directive 2014/30/EUEN 61326-1:2013 (industrial locations): . Directive 2014/30/EU: EN 61326-1:2013 (industrial locations). Electromagnetic compatibility: NE 21:2012 EN 61326-3-2:2008. Degree of protection: IEC 60529:2001. Protection against electrical shock: UL 61010-1:2012. Ambient temperature: -20 … 60 °C (-4 … 140 °F) extended ambient temperature range up to 70 °C (158 °F), refer to manual for necessary mounting conditions. Degree of protection: IP20. Connection: screw terminals. Mass: approx. 200 g. Dimensions: 20 x 124 x 115 mm (0.8 x 4.9 x 4.5 inch) (W x H x D) , housing type B2. Height124 mmWidth20 mmDepth115 mm: . Height: 124 mm. Width: 20 mm. Depth: 115 mm. Mounting: on 35 mm DIN mounting rail acc. to EN 60715:2001. EU-type examination certificate: CML 17 ATEX 2031X. Marking II (1)G [Ex ia Ga] IIC [exsign] II (1)D [Ex ia Da] IIIC [exsign] I (M1) [Ex ia Ma] IInput[Ex ia Ga] IIC, [Ex ia Da] IIIC, [Ex ia Ma] I: . Marking: II (1)G [Ex ia Ga] IIC [exsign] II (1)D [Ex ia Da] IIIC [exsign] I (M1) [Ex ia Ma] I. Input: [Ex ia Ga] IIC, [Ex ia Da] IIIC, [Ex ia Ma] I. Supply: . Maximum safe voltageUm250 V (Attention! The rated voltage can be lower.): Um. Maximum safe voltage: 250 V (Attention! The rated voltage can be lower.). Equipment: terminals 1+, 3-; 4+, 6-. VoltageUo26.2 VVoltageUq27.25 VCurrentIo93 mAPowerPo634 mW: Uo. Voltage: 26.2 V. Voltage: 27.25 V. Current: 93 mA. Power: 634 mW. Equipment: terminals 2-, 3+; 5-, 6+. VoltageUi30 VCurrentIi115 mAPowerPimax 1 WVoltageUo2 VCurrentIo8.5 mAPowerPo4.3 mW: Ui. Voltage: 30 V. Current: 115 mA. Power: max 1 W. Voltage: 2 V. Current: 8.5 mA. Power: 4.3 mW. Equipment: terminals 1+, 2/3-; 4+, 5/6-. VoltageUo26.2 VVoltageUq27.25 VCurrentIo115 mAPowerPo784 mW: Uo. Voltage: 26.2 V. Voltage: 27.25 V. Current: 115 mA. Power: 784 mW. Certificate: CML 17 ATEX 3030X. Marking II 3G Ex ec IIC T4 Gc: . Marking: II 3G Ex ec IIC T4 Gc. Galvanic isolation: . Input/Outputsafe electrical isolation acc. to IEC/EN 60079-11:2007, voltage peak value 375 VInput/power supplysafe electrical isolation acc. to IEC/EN 60079-11:2007, voltage peak value 375 V: . Input/Output: safe electrical isolation acc. to IEC/EN 60079-11:2007, voltage peak value 375 V. Input/power supply: safe electrical isolation acc. to IEC/EN 60079-11:2007, voltage peak value 375 V. Directive conformity: . Directive 2014/34/EUEN IEC 60079-0:2018+AC:2020 , EN 60079-7:2015+A1:2018 , EN 60079-11:2012: . Directive 2014/34/EU: EN IEC 60079-0:2018+AC:2020 , EN 60079-7:2015+A1:2018 , EN 60079-11:2012. UL approval: E106378. Control drawing116-0439 (cULus): . Control drawing: 116-0439 (cULus). IECEx approval: . IECEx certificateIECEx CML 17.0016XIECEx marking[Ex ia Ga] IIC , [Ex ia Da] IIIC , [Ex ia Ma] I Ex ec IIC T4 Gc: . IECEx certificate: IECEx CML 17.0016X. IECEx marking: [Ex ia Ga] IIC , [Ex ia Da] IIIC , [Ex ia Ma] I Ex ec IIC T4 Gc. Supplementary information: Observe the certificates, declarations of conformity, instruction manuals, and manuals where applicable. For information see www.pepperl-fuchs.com.

The post Pepperl Fuchs KFD2-STC5-Ex2 appeared first on CentralXL | Industrial Marketplace.

Pepperl Fuchs KFD2-STC5-Ex1.2O

sales@partnerplc.com — Tue, 20 Jan 2026 13:29:39 +0000

SMART Transmitter Power Supply. 1-channel isolated barrier, 24 V DC supply (Power Rail), Input 2-wire and 3-wire SMART transmitters and 2-wire SMART current sources, Signal splitter (1 input and 2 outputs), Dual output 4 mA … 20 mA current sink/current source, Terminals with test points, Up to SIL 2 (SC 3) acc. to IEC/EN 61508, Housing width: 20 mm, Number of channels: 1-channel, HART communication, Test sockets, Safety Integrity Level (SIL): SIL 3, Systematic capability (SC): SC 3, Rated voltage: 18 … 30 V DC. Signal type: Analog input. Safety Integrity Level (SIL): SIL 3. Systematic capability (SC): SC 3. Connection: Power Rail or terminals 14+, 15-. Rated voltage: 18 … 30 V DC. Ripple: within the supply tolerance. Power dissipation: ≤ 1 W at maximum load. Power consumption: ≤ 1.7 W at maximum load. Connection side: field side. Connection: terminals 1+, 2-, 3. Input signal: 4 … 20 mA. Open circuit voltage/short-circuit current: terminals 1+, 3: 23 V / 25 mA. Input resistance: max. 265 Ω terminals 2-, 3 , max. 330 Ω terminals 1+, 3. Available voltage: ≥ 16 V at 20 mA ; ≥ 20 V at 4 mA , terminals 1+, 3. Connection side: control side. Connection: terminals 7+, 8-, 9-; 10+, 11-, 12- (sink)terminals 7-, 8+, 9+; 10-, 11+, 12+ (source) see additional information. Load: 0 … 600 Ω. Output signal: 4 … 20 mA (overload > 25 mA). Ripple: max. 50 µA rms. External supply (loop): 2 … 30 V DC If the external voltage is > 19 V, a load ≥ ((V – 19) / 0.02) Ω is required. V represents the value of the external voltage. The internal 250 Ω resistor at terminals 9 and 12 can be used as a load.. Deviation: at 20 °C (68 °F), 4 … 20 mA≤ 10 µA incl. calibration, linearity, hysteresis, loads and fluctuations of supply voltage. Influence of ambient temperature≤ 0.25 µA/K: . Influence of ambient temperature: ≤ 0.25 µA/K. Frequency range: field side into the control side: bandwidth with 0.5 Vpp signal 0 … 7.5 kHz (-3 dB) control side into the field side: bandwidth with 0.5 Vpp signal 0.3 … 7.5 kHz (-3 dB). Settling time: 200 µs. Rise time/fall time: 100 µs. Output/power supply: functional insulation, rated insulation voltage 50 V AC. Output/Output: functional insulation, rated insulation voltage 50 V AC. Display elements: LED. Labeling: space for labeling at the front. Electromagnetic compatibility: . Directive 2014/30/EUEN 61326-1:2013 (industrial locations): . Directive 2014/30/EU: EN 61326-1:2013 (industrial locations). Electromagnetic compatibility: NE 21:2012 EN 61326-3-2:2008. Degree of protection: IEC 60529:2001. Protection against electrical shock: UL 61010-1:2012. Ambient temperature: -20 … 60 °C (-4 … 140 °F) extended ambient temperature range up to 70 °C (158 °F), refer to manual for necessary mounting conditions. Degree of protection: IP20. Connection: screw terminals. Mass: approx. 200 g. Dimensions: 20 x 124 x 115 mm (0.8 x 4.9 x 4.5 inch) (W x H x D) , housing type B2. Mounting: on 35 mm DIN mounting rail acc. to EN 60715:2001. EU-type examination certificate: CML 17 ATEX 2031X. Marking II (1)G [Ex ia Ga] IIC [exsign] II (1)D [Ex ia Da] IIIC [exsign] I (M1) [Ex ia Ma] IInput[Ex ia Ga] IIC, [Ex ia Da] IIIC, [Ex ia Ma] I: . Marking: II (1)G [Ex ia Ga] IIC [exsign] II (1)D [Ex ia Da] IIIC [exsign] I (M1) [Ex ia Ma] I. Input: [Ex ia Ga] IIC, [Ex ia Da] IIIC, [Ex ia Ma] I. Supply: . Maximum safe voltageUm250 V (Attention! The rated voltage can be lower.): Um. Maximum safe voltage: 250 V (Attention! The rated voltage can be lower.). Equipment: terminals 1+, 3-. VoltageUo26.2 VVoltageUq27.25 VCurrentIo93 mAPowerPo634 mW: Uo. Voltage: 26.2 V. Voltage: 27.25 V. Current: 93 mA. Power: 634 mW. Equipment: terminals 2-, 3. VoltageUi30 VCurrentIi115 mAPowerPimax 1 WVoltageUo2 VCurrentIo8.5 mAPowerPo4.3 mW: Ui. Voltage: 30 V. Current: 115 mA. Power: max 1 W. Voltage: 2 V. Current: 8.5 mA. Power: 4.3 mW. Equipment: terminals 1+, 2 / 3-. VoltageUo26.2 VVoltageUq27.25 VCurrentIo115 mAPowerPo784 mW: Uo. Voltage: 26.2 V. Voltage: 27.25 V. Current: 115 mA. Power: 784 mW. Certificate: CML 17 ATEX 3030X. Marking II 3G Ex ec IIC T4 Gc: . Marking: II 3G Ex ec IIC T4 Gc. Galvanic isolation: . Input/Outputsafe electrical isolation acc. to IEC/EN 60079-11:2007, voltage peak value 375 VInput/power supplysafe electrical isolation acc. to IEC/EN 60079-11:2007, voltage peak value 375 V: . Input/Output: safe electrical isolation acc. to IEC/EN 60079-11:2007, voltage peak value 375 V. Input/power supply: safe electrical isolation acc. to IEC/EN 60079-11:2007, voltage peak value 375 V. Directive conformity: . Directive 2014/34/EUEN IEC 60079-0:2018+AC:2020 , EN 60079-7:2015+A1:2018 , EN 60079-11:2012: . Directive 2014/34/EU: EN IEC 60079-0:2018+AC:2020 , EN 60079-7:2015+A1:2018 , EN 60079-11:2012. UL approval: E106378. Control drawing116-0439 (cULus): . Control drawing: 116-0439 (cULus). IECEx approval: . IECEx certificateIECEx CML 17.0016XIECEx marking[Ex ia Ga] IIC , [Ex ia Da] IIIC , [Ex ia Ma] I Ex ec IIC T4 Gc: . IECEx certificate: IECEx CML 17.0016X. IECEx marking: [Ex ia Ga] IIC , [Ex ia Da] IIIC , [Ex ia Ma] I Ex ec IIC T4 Gc. Supplementary information: Observe the certificates, declarations of conformity, instruction manuals, and manuals where applicable. For information see www.pepperl-fuchs.com.

The post Pepperl Fuchs KFD2-STC5-Ex1.2O appeared first on CentralXL | Industrial Marketplace.

Pepperl Fuchs KFD2-SCD2-Ex2.LK

sales@partnerplc.com — Tue, 20 Jan 2026 13:29:36 +0000

SMART Current Driver. 2-channel isolated barrier, 24 V DC supply (Power Rail), Current output up to 650 Ω load, HART-IP and valve positioner, Line fault detection (LFD), Accuracy 0.1 %, Up to SIL 2 (SC 3) acc. to IEC/EN 61508, Housing width: 20 mm, Number of channels: 2-channel, Transfer direction: to the field, HART communication, Test sockets, Safety Integrity Level (SIL): SIL 2, Systematic capability (SC): SC 3, Rated voltage: 19 … 30 V DC, Signal: 2 x 4 … 20 mA, Line fault detection. Signal type: Analog output. Safety Integrity Level (SIL): SIL 2. Systematic capability (SC): SC 3. Connection: Power Rail or terminals 14+, 15-. Rated voltage: 19 … 30 V DC. Ripple: ≤ 10 %. Rated current: ≤ 45 mA at 24 V. Power dissipation: ≤ 1 W at 20 mA and 500 Ω load. Power consumption: ≤ 1 W. Connection side: control side. Connection: terminals 7-, 8+, (9+); 10-, 11+, (12+). Input signal: 4 … 20 mA , limited to approx. 30 mA. Input voltage: open loop voltage of the control system ≤ 30 V. Voltage drop: approx. 6 V at 20 mA. Input resistance: field wiring open circuit : > 100 kΩ field wiring 100 kΩ when using terminals 1, 2 and 4, 5. Connection side: field side. Connection: terminals 1+, 2-; 4+, 5- terminals 3+, 2-; 6+, 5- (no short circuit detection). Voltage: ≥ 13 V at 20 mA. Current: 4 … 20 mA. Load: 100 … 650 Ω , for terminals 1, 2; 4, 5 0 … 550 Ω , for Terminals 2, 3; 5, 6. Ripple: 20 mV rms. Line fault detection: breakage, load > 100 kΩ, short-circuit, load < 50 Ω. Output type: open collector transistor (internal fault bus). Deviation: at 20 °C (68 °F), 4 … 20 mA< 0.1 % of full scale, incl. non-linearity and hysteresis. Influence of ambient temperature< 2 µA/K (-20 … 70 °C (-4 … 158 °F)); < 4 µA/K (-40 … -20 °C (-40 … -4 °F)): . Influence of ambient temperature: < 2 µA/K (-20 … 70 °C (-4 … 158 °F)); < 4 µA/K (-40 … -20 °C (-40 … -4 °F)). Frequency range: field side into the control side: bandwidth with 0.5 Vpp signal 0 … 3 kHz (-3 dB) control side into the field side: bandwidth with 0.5 Vpp signal 0 … 3 kHz (-3 dB). Rise time: 10 to 90 % ≤ 10 ms. Input/Output: basic insulation according to IEC/EN 61010-1, rated insulation voltage 300 Veff. Input/power supply: basic insulation according to IEC/EN 61010-1, rated insulation voltage 300 Veff. Output/power supply: reinforced insulation according to IEC/EN 61010-1, rated insulation voltage 300 Veff. Input/input: functional insulation, rated insulation voltage 50 V AC. Display elements: LEDs. Labeling: space for adhesive label at the front. Electromagnetic compatibility: . Directive 2014/30/EUEN 61326-1:2013 (industrial locations): . Directive 2014/30/EU: EN 61326-1:2013 (industrial locations). Electromagnetic compatibility: NE 21:2017 EN 61326-3-2:2018. Degree of protection: IEC 60529. Protection against electrical shock: UL 61010-1:2012. Ambient temperature: -40 … 70 °C (-40 … 158 °F). Degree of protection: IP20. Connection: screw terminals. Mass: approx. 135 g. Dimensions: 20 x 124 x 115 mm (0.8 x 4.9 x 4.5 inch) (W x H x D) , housing type B2. Mounting: on 35 mm DIN mounting rail acc. to EN 60715:2001. EU-type examination certificate: BAS 00 ATEX 7240 X. Marking II (1)G [Ex ia Ga] IIC [exsign] II (1)D [Ex ia Da] IIIC [exsign] I (M1) [Ex ia Ma] IOutputEx ia, Ex iaDVoltageUo25.2 VCurrentIo93 mAPowerPo585.3 mWInternal capacitanceCi1.05 nFInternal inductanceLi 0: . Marking: II (1)G [Ex ia Ga] IIC [exsign] II (1)D [Ex ia Da] IIIC [exsign] I (M1) [Ex ia Ma] I. Output: Ex ia, Ex iaD. Voltage: 25.2 V. Current: 93 mA. Power: 585.3 mW. Internal capacitance: 1.05 nF. Internal inductance: 0. Supply: . Maximum safe voltageUm250 V rms (Attention! The rated voltage can be lower.): Um. Maximum safe voltage: 250 V rms (Attention! The rated voltage can be lower.). Input: . Maximum safe voltageUm250 V rms (Attention! The rated voltage can be lower.): Um. Maximum safe voltage: 250 V rms (Attention! The rated voltage can be lower.). Certificate: FIDI 22 ATEX 0002 X. Marking II 3G Ex ec IIC T4 Gc: . Marking: II 3G Ex ec IIC T4 Gc. Galvanic isolation: . Input/Outputsafe electrical isolation acc. to IEC/EN 60079-11, voltage peak value 375 VOutput/power supplysafe electrical isolation acc. to IEC/EN 60079-11, voltage peak value 375 V: . Input/Output: safe electrical isolation acc. to IEC/EN 60079-11, voltage peak value 375 V. Output/power supply: safe electrical isolation acc. to IEC/EN 60079-11, voltage peak value 375 V. Directive conformity: . Directive 2014/34/EUEN IEC 60079-0:2018 , EN 60079-11:2012 , EN IEC 60079-7:2015+A1:2018: . Directive 2014/34/EU: EN IEC 60079-0:2018 , EN 60079-11:2012 , EN IEC 60079-7:2015+A1:2018. UL approval: E106378. Control drawing116-0345 (cULus): . Control drawing: 116-0345 (cULus). IECEx approval: . IECEx certificateIECEx BAS 04.0014XIECEx marking[Ex ia Ga] IIC , [Ex ia Da] IIIC , [Ex ia Ma] I Ex ec IIC T4 Gc: . IECEx certificate: IECEx BAS 04.0014X. IECEx marking: [Ex ia Ga] IIC , [Ex ia Da] IIIC , [Ex ia Ma] I Ex ec IIC T4 Gc. Supplementary information: Observe the certificates, declarations of conformity, instruction manuals, and manuals where applicable. For information see www.pepperl-fuchs.com.

The post Pepperl Fuchs KFD2-SCD2-Ex2.LK appeared first on CentralXL | Industrial Marketplace.

Pepperl Fuchs KFD2-SCD2-Ex1.LK

sales@partnerplc.com — Tue, 20 Jan 2026 13:29:35 +0000

SMART Current Driver. 1-channel isolated barrier, 24 V DC supply (Power Rail), Current output up to 650 Ω load, HART-IP and valve positioner, Line fault detection (LFD), Accuracy 0.1 %, Up to SIL 2 (SC 3) acc. to IEC/EN 61508, Housing width: 20 mm, Number of channels: 1-channel, Transfer direction: to the field, HART communication, Test sockets, Safety Integrity Level (SIL): SIL 2, Systematic capability (SC): SC 3, Rated voltage: 19 … 30 V DC, Signal: 2 x 4 … 20 mA, Line fault detection. Signal type: Analog output. Safety Integrity Level (SIL): SIL 2. Systematic capability (SC): SC 3. Connection: Power Rail or terminals 14+, 15-. Rated voltage: 19 … 30 V DC. Ripple: ≤ 10 %. Rated current: ≤ 30 mA at 24 V. Power dissipation: ≤ 600 mW at 20 mA and 500 Ω load. Power consumption: ≤ 700 mW. Connection side: control side. Connection: terminals 7-, 8+, (9+). Input signal: 4 … 20 mA , limited to approx. 30 mA. Input voltage: open loop voltage of the control system ≤ 30 V. Voltage drop: approx. 6 V at 20 mA. Input resistance: field wiring open circuit : > 100 kΩ field wiring 100 kΩ when using terminals 1 and 2. Connection side: field side. Connection: terminals 1+, 2- terminals 3+, 2- (no short circuit detection). Voltage: ≥ 13 V at 20 mA. Current: 4 … 20 mA. Load: 100 … 650 Ω , for terminals 1, 2 0 … 550 Ω , for terminals 2, 3. Ripple: 20 mV rms. Line fault detection: breakage, load > 100 kΩ, short-circuit, load < 50 Ω. Output type: open collector transistor (internal fault bus). Deviation: at 20 °C (68 °F), 4 … 20 mA< 0.1 % of full scale, incl. non-linearity and hysteresis. Influence of ambient temperature< 2 µA/K (-20 … 70 °C (-4 … 158 °F)); < 4 µA/K (-40 … -20 °C (-40 … -4 °F)): . Influence of ambient temperature: < 2 µA/K (-20 … 70 °C (-4 … 158 °F)); < 4 µA/K (-40 … -20 °C (-40 … -4 °F)). Frequency range: field side into the control side: bandwidth with 0.5 Vpp signal 0 … 3 kHz (-3 dB) control side into the field side: bandwidth with 0.5 Vpp signal 0 … 3 kHz (-3 dB). Rise time: 10 to 90 % ≤ 10 ms. Input/Output: basic insulation according to IEC/EN 61010-1, rated insulation voltage 300 Veff. Input/power supply: basic insulation according to IEC/EN 61010-1, rated insulation voltage 300 Veff. Output/power supply: reinforced insulation according to IEC/EN 61010-1, rated insulation voltage 300 Veff. Display elements: LEDs. Labeling: space for adhesive label at the front. Electromagnetic compatibility: . Directive 2014/30/EUEN 61326-1:2013 (industrial locations): . Directive 2014/30/EU: EN 61326-1:2013 (industrial locations). Electromagnetic compatibility: NE 21:2017 EN 61326-3-2:2018. Degree of protection: IEC 60529. Protection against electrical shock: UL 61010-1:2012. Ambient temperature: -40 … 70 °C (-40 … 158 °F). Degree of protection: IP20. Connection: screw terminals. Mass: approx. 115 g. Dimensions: 20 x 124 x 115 mm (0.8 x 4.9 x 4.5 inch) (W x H x D) , housing type B2. Mounting: on 35 mm DIN mounting rail acc. to EN 60715:2001. EU-type examination certificate: BAS 00 ATEX 7240 X. Marking II (1)G [Ex ia Ga] IIC [exsign] II (1)D [Ex ia Da] IIIC [exsign] I (M1) [Ex ia Ma] IOutputEx ia, Ex iaDVoltageUo25.2 VCurrentIo93 mAPowerPo585.3 mWInternal capacitanceCi1.05 nFInternal inductanceLi 0: . Marking: II (1)G [Ex ia Ga] IIC [exsign] II (1)D [Ex ia Da] IIIC [exsign] I (M1) [Ex ia Ma] I. Output: Ex ia, Ex iaD. Voltage: 25.2 V. Current: 93 mA. Power: 585.3 mW. Internal capacitance: 1.05 nF. Internal inductance: 0. Supply: . Maximum safe voltageUm250 V rms (Attention! The rated voltage can be lower.): Um. Maximum safe voltage: 250 V rms (Attention! The rated voltage can be lower.). Input: . Maximum safe voltageUm250 V rms (Attention! The rated voltage can be lower.): Um. Maximum safe voltage: 250 V rms (Attention! The rated voltage can be lower.). Certificate: FIDI 22 ATEX 0002 X. Marking II 3G Ex ec IIC T4 Gc: . Marking: II 3G Ex ec IIC T4 Gc. Galvanic isolation: . Input/Outputsafe electrical isolation acc. to IEC/EN 60079-11, voltage peak value 375 VOutput/power supplysafe electrical isolation acc. to IEC/EN 60079-11, voltage peak value 375 V: . Input/Output: safe electrical isolation acc. to IEC/EN 60079-11, voltage peak value 375 V. Output/power supply: safe electrical isolation acc. to IEC/EN 60079-11, voltage peak value 375 V. Directive conformity: . Directive 2014/34/EUEN IEC 60079-0:2018 , EN 60079-11:2012 , EN IEC 60079-7:2015+A1:2018: . Directive 2014/34/EU: EN IEC 60079-0:2018 , EN 60079-11:2012 , EN IEC 60079-7:2015+A1:2018. UL approval: E106378. Control drawing116-0345 (cULus): . Control drawing: 116-0345 (cULus). IECEx approval: . IECEx certificateIECEx BAS 04.0014XIECEx marking[Ex ia Ga] IIC , [Ex ia Da] IIIC , [Ex ia Ma] I Ex ec IIC T4 Gc: . IECEx certificate: IECEx BAS 04.0014X. IECEx marking: [Ex ia Ga] IIC , [Ex ia Da] IIIC , [Ex ia Ma] I Ex ec IIC T4 Gc. Supplementary information: Observe the certificates, declarations of conformity, instruction manuals, and manuals where applicable. For information see www.pepperl-fuchs.com.

The post Pepperl Fuchs KFD2-SCD2-Ex1.LK appeared first on CentralXL | Industrial Marketplace.

Pepperl Fuchs KFD2-GUT-Ex1.D

sales@partnerplc.com — Tue, 20 Jan 2026 13:29:34 +0000

Temperature Converter with Trip Values. 1-channel isolated barrier, 24 V DC supply (Power Rail), Thermocouple, RTD, potentiometer or voltage input, Redundant TC input, Current output 0/4 mA … 20 mA, 2 relay contact outputs, Configurable by PACTware or keypad, Line fault (LFD) and sensor burnout detection, Up to SIL 2 acc. to IEC/EN 61508 / IEC/EN 61511, Housing width: 40 mm, Number of channels: 1-channel, Trip relay, Safety Integrity Level (SIL): SIL 2, Rated voltage: 20 … 30 V DC, Type: 2-wire connection. Signal type: Analog input. Safety Integrity Level (SIL): SIL 2. Connection: terminals 23+, 24- or power feed module/Power Rail. Rated voltage: 20 … 30 V DC. Rated current: approx. 100 mA. Power dissipation/power consumption: ≤ 2 W / 2.2 W. Programming interface: programming socket. Connection side: field side. Connection: terminals 1, 2, 3, 4, 6. RTD: Pt100, Pt500, Pt1000, Ni100, Ni1000. Types of measuring2-, 3-, 4-wire technologyLead resistancemax. 50 ΩMeasurement loop monitoringsensor breakage, sensor short-circuit: . Types of measuring: 2-, 3-, 4-wire technology. Lead resistance: max. 50 Ω. Measurement loop monitoring: sensor breakage, sensor short-circuit. Thermocouples: type B, E, J, K, L, N, R, S, T (IEC 584-1: 1995). Cold junction compensationexternal and internalMeasurement loop monitoringsensor breakage: . Cold junction compensation: external and internal. Measurement loop monitoring: sensor breakage. Potentiometer: 0.8 … 20 kΩ. Types of measuring2-, 3-, 5-wire technology: . Types of measuring: 2-, 3-, 5-wire technology. Voltage: 0 … 10 V , 2 … 10 V , 0 … 1 V , -100 … 100 mV. Input resistance: ≥ 250 kΩ (0 … 10 V) min. 1 MΩ (0 … 1 V, -100 … 100 mV). Measuring current: approx. 400 µA with resistance measuring sensor. Connection side: control side. Connection: output I: terminals 10, 11, 12 output II: terminals 16, 17, 18 output III: terminals 8+, 7-. Output I, II: relay. Contact loading250 V AC / 2 A / cos φ ≥ 0.7 ; 40 DC / 2 AMechanical life5 x 107 switching cyclesEnergized/De-energized delayapprox. 20 ms / approx. 20 ms: . Contact loading: 250 V AC / 2 A / cos φ ≥ 0.7 ; 40 DC / 2 A. Mechanical life: 5 x 107 switching cycles. Energized/De-energized delay: approx. 20 ms / approx. 20 ms. Output III: Analog current output. Current range0 … 20 mA or 4 … 20 mAOpen loop voltagemax. 24 V DCLoadmax. 650 ΩFault signaldownscale I ≤ 3.6 mA, upscale I ≥ 21 mA (acc. NAMUR NE43): . Current range: 0 … 20 mA or 4 … 20 mA. Open loop voltage: max. 24 V DC. Load: max. 650 Ω. Fault signal: downscale I ≤ 3.6 mA, upscale I ≥ 21 mA (acc. NAMUR NE43). Collective error message: Power Rail. Deviation: . Temperature effect Input: 0.005 %/K (50 ppm) of span ; current output: 0.005 %/K (50 ppm) of spanRTDmax. 0.2 % of spanThermocouplesmax. 10µV deviation of CJC: ±0.8 KVoltage0.1 % of spanPotentiometer0.1 % of span when 5 kΩCurrent outputmax. 20 µA: . Temperature effect: Input: 0.005 %/K (50 ppm) of span ; current output: 0.005 %/K (50 ppm) of span. RTD: max. 0.2 % of span. Thermocouples: max. 10µV deviation of CJC: ±0.8 K. Voltage: 0.1 % of span. Potentiometer: 0.1 % of span when 5 kΩ. Current output: max. 20 µA. Sampling rate: approx. 700 ms. Input/Other circuits: reinforced insulation according to IEC/EN 61010-1, rated insulation voltage 300 Veff. Output I, II against eachother: reinforced insulation according to IEC/EN 61010-1, rated insulation voltage 300 Veff. Output I, II/other circuits: reinforced insulation according to IEC/EN 61010-1, rated insulation voltage 300 Veff. Output III/power supply and collective error: reinforced insulation according to IEC/EN 61010-1, rated insulation voltage 300 Veff. Interface/power supply: reinforced insulation according to IEC/EN 61010-1, rated insulation voltage 300 Veff. Display elements: LEDs , display. Control elements: Control panel. Configuration: via operating buttons via PACTware. Labeling: space for labeling at the front. Electromagnetic compatibility: . Directive 2014/30/EUEN 61326-1:2013 (industrial locations): . Directive 2014/30/EU: EN 61326-1:2013 (industrial locations). Low voltage: . Directive 2014/35/EUEN 61010-1:2010: . Directive 2014/35/EU: EN 61010-1:2010. Electromagnetic compatibility: NE 21:2007. Degree of protection: IEC 60529:2001. Ambient temperature: -20 … 60 °C (-4 … 140 °F). Degree of protection: IP20. Connection: screw terminals. Mass: 300 g. Dimensions: 40 x 119 x 115 mm (1.6 x 4.7 x 4.5 inch) (W x H x D) , housing type C2. Mounting: on 35 mm DIN mounting rail acc. to EN 60715:2001. EU-type examination certificate: TÜV 03 ATEX 2140. Marking II (1)G [Ex ia Ga] IIC [exsign] II (1)D [Ex ia Da] IIIC [exsign] I (M1) [Ex ia Ma] IInputEx ia: . Marking: II (1)G [Ex ia Ga] IIC [exsign] II (1)D [Ex ia Da] IIIC [exsign] I (M1) [Ex ia Ma] I. Input: Ex ia. Supply: . Maximum safe voltageUm40 V DC (Attention! The rated voltage can be lower.): Um. Maximum safe voltage: 40 V DC (Attention! The rated voltage can be lower.). Input: terminals 2, 6 (for active equipment). VoltageUo13.1 VCurrentIo8 mAPowerPo67 mWVoltageUi29 VCurrentIi11 mAPowerPi200 mW: Uo. Voltage: 13.1 V. Current: 8 mA. Power: 67 mW. Voltage: 29 V. Current: 11 mA. Power: 200 mW. Inputs: terminals 1, 2, 3, 4, 6 (for passive equipment). Voltage Uo13.1 VCurrent Io21 mAPower Po67 mW: . Voltage Uo: 13.1 V. Current Io: 21 mA. Power Po: 67 mW. Analog output: . Maximum safe voltageUm40 V (Attention! The rated voltage can be lower.): Um. Maximum safe voltage: 40 V (Attention! The rated voltage can be lower.). Interface: . Maximum safe voltageUm40 V (Attention! The rated voltage can be lower.) , RS 232: Um. Maximum safe voltage: 40 V (Attention! The rated voltage can be lower.) , RS 232. Certificate: PF 08 CERT 1213 X. Marking II 3G Ex nA nC IIC T4 Gc: . Marking: II 3G Ex nA nC IIC T4 Gc. Output I, II: . Contact loading50 V AC/2 A/cos φ > 0.7; 40 V DC/1 A resistive load: . Contact loading: 50 V AC/2 A/cos φ > 0.7; 40 V DC/1 A resistive load. Galvanic isolation: . Input/Other circuitssafe electrical isolation acc. to IEC/EN 60079-11, voltage peak value 375 V: . Input/Other circuits: safe electrical isolation acc. to IEC/EN 60079-11, voltage peak value 375 V. Directive conformity: . Directive 2014/34/EUEN IEC 60079-0:2018+AC:2020 , EN 60079-11:2012 , EN 60079-15:2010: . Directive 2014/34/EU: EN IEC 60079-0:2018+AC:2020 , EN 60079-11:2012 , EN 60079-15:2010. IECEx approval: . IECEx certificateIECEx TUN 09.0019IECEx marking[Ex ia Ga] IIC , [Ex ia Da] IIIC , [Ex ia Ma] I: . IECEx certificate: IECEx TUN 09.0019. IECEx marking: [Ex ia Ga] IIC , [Ex ia Da] IIIC , [Ex ia Ma] I. Supplementary information: Observe the certificates, declarations of conformity, instruction manuals, and manuals where applicable. For information see www.pepperl-fuchs.com.

The post Pepperl Fuchs KFD2-GUT-Ex1.D appeared first on CentralXL | Industrial Marketplace.

Pepperl Fuchs KFD0-TR-Ex1

sales@partnerplc.com — Tue, 20 Jan 2026 13:29:24 +0000

RTD Converter. 1-channel isolated barrier, 24 V DC supply (loop powered), 2- or 3-wire Pt100 RTD input, Output 4 mA … 20 mA, temperature linearization selectable, DIP switch selectable ranges, Sensor breakage detection, Housing width: 20 mm, Number of channels: 1-channel, Rated voltage: 12 … 35 V DC loop powered, Type: 3-wire connection, Field device: resistance thermometer, Signal: 1 x 4 … 20 mA (current sink). Signal type: Analog input. Rated voltage: 12 … 35 V DC loop powered. Power dissipation: 0.4 W. Connection side: field side. Connection: terminals 1, 2-, 3+ suitable for Pt100, 2- and 3-wire connection. Lead resistance: max. 100 Ω per line. Measuring current: approx. 1 mA. Connection side: control side. Connection: terminals 9+, 8-. Load: (U -12 V) / 0.02 A. Current output: 4 … 20 mA , limited to ≤ 35 mA. Fault signal: upscaling ≥ 22 mA (limited to 35 mA). Measuring range: span without linearization 25 … 800 °C (77 … 1472 °F)/with linearization 25 … 375 °C (77 … 707 °F), both adjustable zero point without linearization -200 … 400 °C (-328 … 752 °F)/with linearization -30 … 375 °C (-22 … 707 °F), both adjustable. Deviation: . After calibration0.1 % of full-scale value incl. linearity and hysteresisInfluence of ambient temperaturespan and zero point 0.015 % / K or ± 10 mΩ / KInfluence of supply voltage6.5 ppm/V: . After calibration: 0.1 % of full-scale value incl. linearity and hysteresis. Influence of ambient temperature: span and zero point 0.015 % / K or ± 10 mΩ / K. Influence of supply voltage: 6.5 ppm/V. Rise time: 250 ms. Input/Output: available. Control elements: DIP switch rotary switch. Configuration: via DIP switches via rotary switch. Labeling: space for labeling at the front. Electromagnetic compatibility: . Directive 2014/30/EUEN 61326-1:2013 (industrial locations): . Directive 2014/30/EU: EN 61326-1:2013 (industrial locations). Insulation coordination: EN 50178. Galvanic isolation: EN 50178. Degree of protection: IEC 60529. Ambient temperature: -20 … 60 °C (-4 … 140 °F). Degree of protection: IP20. Connection: screw terminals. Mass: approx. 150 g. Dimensions: 20 x 119 x 115 mm (0.8 x 4.7 x 4.5 inch) (W x H x D) , housing type B2. Height119 mmWidth20 mmDepth115 mm: . Height: 119 mm. Width: 20 mm. Depth: 115 mm. Mounting: on 35 mm DIN mounting rail acc. to EN 60715:2001. EU-type examination certificate: ZELM 00 ATEX 0036. Marking II (1)GD [EEx ia] IICVoltageUo16.1 VCurrentIo33 mAPowerPo131 mW: . Marking: II (1)GD [EEx ia] IIC. Voltage: 16.1 V. Current: 33 mA. Power: 131 mW. Certificate: TÜV 01 ATEX 1777 X. Marking II 3G Ex nA II T4: . Marking: II 3G Ex nA II T4. Galvanic isolation: . Input/Outputsafe electrical isolation acc. to IEC/EN 60079-11, voltage peak value 375 V: . Input/Output: safe electrical isolation acc. to IEC/EN 60079-11, voltage peak value 375 V. Directive conformity: . Directive 2014/34/EUEN IEC 60079-0:2018+AC:2020 , EN 60079-11:2012 , EN 60079-15:2010: . Directive 2014/34/EU: EN IEC 60079-0:2018+AC:2020 , EN 60079-11:2012 , EN 60079-15:2010. CSA approval: 1029981. Control drawing116-0132: . Control drawing: 116-0132. IECEx approval: . IECEx certificateIECEx TUN 06.0004IECEx marking[Zone 0] [Ex ia] IIC: . IECEx certificate: IECEx TUN 06.0004. IECEx marking: [Zone 0] [Ex ia] IIC. Supplementary information: Observe the certificates, declarations of conformity, instruction manuals, and manuals where applicable. For information see www.pepperl-fuchs.com.

The post Pepperl Fuchs KFD0-TR-Ex1 appeared first on CentralXL | Industrial Marketplace.