Fast delivery within 72 Hours
B&R 8V1022.001-2
Modular mechanical design using plug-in modulesIntegrated line filterIntegrated braking resistorAll connections are made using plug-in connectorsIntegrated electronic restart inhibitPartially-coated c…
Shipping & Delivery
-
Courier delivery
Our courier will deliver to the specified address
2-3 Days
From $20
-
DHL Courier delivery
DHL courier will deliver to the specified address
2-3 Days
From $40
-
Warranty 1 year
-
Free 30-Day returns
Description
Modular mechanical design using plug-in modulesIntegrated line filterIntegrated braking resistorAll connections are made using plug-in connectorsIntegrated electronic restart inhibitPartially-coated circuit boards – more robust in regard to environmental influences (8Vxxxx.001-2)
ACOPOS servo drive, 3x 400-480 V, 2.2 A, 1 kW, coated, integrated line filter, braking resistor and electronic safe restart interlock
Specification
| Note |
Variant with partially coated printed circuit boards |
|---|---|
| B&R ID code |
0xA099 |
| Slots for plug-in modules |
4 |
| CE |
Yes |
| UKCA |
Yes |
| CRA (Cyber Resilience Act) |
Evaluation ongoing |
| Functional safety |
Yes |
| UL |
cULus E225616Power conversion equipment |
| KC |
Yes |
| Permissible network configurations |
TT, TN |
| Mains input voltage |
3x 400 VAC to 480 VAC ±10% 3x 230 VAC ±10% |
| Frequency |
50 / 60 Hz ±4% |
| Installed load |
Max. 3 kVA |
| Inrush current at 400 VAC |
4 A |
| Switch-on interval |
>10 s |
| Integrated line filter per EN 61800-3, category C3 |
Yes |
| Power dissipation at device nominal power without braking resistor |
Approx. 120 W |
| DC bus capacitance |
235 µF |
| Input voltage |
24 VDC ±25% |
| Input capacitance |
8200 µF |
| Current consumption |
Max. 2.5 A + Current for motor holding brake |
| Quantity |
2 |
| Continuous current |
2.2 Aeff |
| Switching frequency 5 kHz |
No reduction |
| Switching frequency 10 kHz |
No reduction |
| Switching frequency 20 kHz |
0.13 Aeff per °C (starting at 51°C) |
| Starting at 500 m above sea level |
0.22 Aeff per 1000 m |
| Peak current |
14 Aeff |
| Nominal switching frequency |
20 kHz |
| Possible switching frequencies |
5 / 10 / 20 kHz |
| Insulation stress of the connected motor per IEC TS 60034-25:2004 |
Limit value curve A |
| Max. motor line length |
25 m |
| Overload protection |
Yes |
| Short-circuit and ground fault protection |
Yes |
| Max. output frequency |
598 Hz |
| With wire end sleeve |
0.25 to 4 mm² |
| UL/C-UL-US |
30 to 10 AWG |
| CSA |
28 to 10 AWG |
| Response threshold for open-circuit monitoring |
Approx. 385 mA |
| Max. output current |
1 A |
| Max. number of switching cycles |
Unlimited since implemented electronically |
| Peak power output |
3.5 kW |
| Continuous power |
130 W |
| Circuit |
Sink |
| Input - ACOPOS |
Yes |
| Input - Input |
No |
| Nominal |
5 to 40°C |
| Maximum |
55°C |
| Low |
<5 V |
| High |
>15 V |
| Input current at nominal voltage |
Approx. 10 mA |
| Switching delay |
Max. 2.0 ms |
| Modulation compared to ground potential |
Max. ±38 V |
| Enable 0 → 1, ready for PWM |
Max. 100 µs |
| Enable 1 → 0, PWM off |
Max. 2.0 ms |
| OSSD signal connections |
Not permitted |
| Rising edge |
52 µs ±0.5 µs (digitally filtered) |
| Falling edge |
53 µs ±0.5 µs (digitally filtered) |
| Discharge capacitance |
660 nF |
| Power dissipation relative to continuous apparent power |
IE2 (10,25) 3.8% IE2 (50,25) 3.8% IE2 (10,50) 4% IE2 (50,50) 4% IE2 (90,50) 4.1% IE2 (10,100) 4.3% IE2 (50,100) 4.4% IE2 (90,100) 4.7% |
| Nominal losses in standby mode |
13.2 W |
| Hanging vertically |
Yes |
| Horizontal, face up |
Yes |
| Standing horizontally |
No |
| Pollution degree per EN 61800-5-1 |
2 (non-conductive pollution) |
| Overvoltage category per EN 61800-5-1 |
II |
| Degree of protection per EN 60529 |
IP20 |
| Storage |
5 to 95% |
| Transport |
Max. 95% at 40°C |
| Operation |
5 to 85% |
| Width |
70.5 mm |
| Height |
375 mm |
| Depth |
235.5 mm |
| Weight |
4.0 kg |
Reviews
Clear filtersThere are no reviews yet.