Fast delivery within 72 Hours
B&R X67BC8513.L12-1
POWERLINK V1/V2Integrated hub for economical wiring12 digital channels, configurable as inputs or outputs1 analog input, 0 to 20 mA, 12-bitM8 connection typeI/O configuration and firmware update via t…
Request for Quote
Shipping & Delivery
-
Courier delivery
Our courier will deliver to the specified address
5-6 Days
From €20
-
DHL Courier delivery
DHL courier will deliver to the specified address
2-3 Days
From €40
-
Warranty 1 year
-
Free 30-Day returns
Description
POWERLINK V1/V2Integrated hub for economical wiring12 digital channels, configurable as inputs or outputs1 analog input, 0 to 20 mA, 12-bitM8 connection typeI/O configuration and firmware update via the fieldbusIntegrated connection to the local expansion via X2X Link for up to 250 additional modulesConfigurable I/O cycle (starting at 200 µs)
The bus controller makes it possible to connect X2X Link I/O nodes to POWERLINK. It is also possible to operate the X2X Link cycle synchronously 1:1 or synchronous to POWERLINK using a prescaler. Additional X2X Link I/O nodes (X67 modules or other modules based on X2X Link) can be connected using the integrated X2X Link connection. Mechanically, POWERLINK is connected via an IP67-rated standard D-coded M12 Ethernet connector.POWERLINK is a standard protocol for Fast Ethernet equipped with hard real-time characteristics. The POWERLINK Standardization Group (EPSG) ensures that the standard remains open and is continually developed:: www.ethernet-powerlink.org.
Specification
| Bus controller | 0x046C |
|---|---|
| Inputs/Outputs | 8x M12, A-coded |
| Insulation voltage between channel and bus | 500 Veff |
| Nominal voltage | 24 VDC |
| Internal I/O module | 0x04A8 |
| Sensor/Actuator power supply | Max. 12 W |
| Status indicators | I/O function per channel, supply voltage, bus function |
| Outputs | Yes, using LED status indicator and software |
| I/O power supply | M8, 4-pin |
| Dynamic node allocation (DNA) | Yes |
| Fieldbus | 200 μs |
| X2X Link | 250 μs |
| Power output | 15 W X2X Link power supply for I/O modules |
| Internal I/O | 0.6 W |
| X2X Link power supply | 17.25 W at maximum power output for connected I/O modules |
| CE | Yes |
| UKCA | Yes |
| CRA (Cyber Resilience Act) | In preparation |
| Type | Type 2 |
| Variant | Current-sourcing FET |
| Line length | Max. 100 m between 2 stations (segment length) |
| Transfer rate | 100 Mbit/s |
| Physical layer | 100BASE-TX |
| Half-duplex | Yes |
| Full-duplex | No |
| Autonegotiation | Yes |
| Auto-MDI/MDIX | Yes |
| Hub propagation delay | 0.96 to 1 µs |
| Synchronization between bus systems possible | Yes |
| Voltage range | 18 to 30 VDC |
| Integrated protective function | Reverse polarity protection |
| Voltage | I/O power supply minus voltage drop for short-circuit protection |
| Voltage drop for short-circuit protection at 0.5 A | Max. 2 VDC |
| Summation current | Max. 0.5 A |
| Short-circuit proof | Yes |
| Input characteristics per EN 61131-2 | Type 1 |
| Input voltage | 18 to 30 VDC |
| Input current at 24 VDC | Typ. 4 mA |
| Input circuit | Sink |
| Input resistance | Typ. 6 kΩ |
| Low | <5 VDC |
| High | >15 VDC |
| Signal form | Square wave pulse |
| Counter size | 16-bit |
| Internal | 10 kHz |
| Pulse length | >200 µs with 200 µs pause between pulses |
| Measurement type | Propagation delay measurement between output and corresponding feedback input |
| Input | 0 to 20 mA |
| Input type | Differential input |
| Digital converter resolution | 12-bit |
| Conversion time | 200 µs |
| Output format | INT |
| Current | 0x0000 – 0x7FFF / 1 LSB = 0x0008 = 4.883 μA |
| Load | <300 Ω |
| Input protection | Protection against wiring with supply voltage |
| Permissible input signal | Max. ±30 mA |
| Undershoot | 0x0000 |
| Overshoot | 0x7FFF |
| Conversion procedure | Successive approximation |
| Gain | 0.1% |
| Offset | 0.05% |
| Max. gain drift | 0.013 %/°C |
| Max. offset drift | 0.02 %/°C |
| DC | >50 dB |
| 50 Hz | >50 dB |
| Common-mode range | ±2 V |
| Crosstalk between channels | >70 dB |
| Nonlinearity | <0.1% |
| Insulation voltage between input and bus | 500 Veff |
| Voltage drop at 20 mA | Typ. 4.5 V |
| Cutoff frequency | 1 kHz |
| Slope | 40 dB |
| Switching voltage | I/O power supply minus residual voltage |
| Nominal output current | 0.5 A |
| Total nominal current | 8 A |
| Output circuit | Source |
| Output protection | Thermal shutdown in the event of overcurrent or short circuit, integrated protection for switching inductive loads, reverse polarity protection of the output power supply |
| Diagnostic status | Output monitoring with 10 ms delay |
| Leakage current when the output is switched off | 5 µA |
| Switching on after overload shutdown | Approx. 10 ms (depends on the module temperature) |
| RDS(on) | 150 mΩ |
| Residual voltage | <0.3 V at 0.5 A nominal current |
| Peak short-circuit current | <12 A |
| 0 → 1 | <400 µs |
| 1 → 0 | <400 µs |
| Resistive load | Max. 100 Hz |
| Inductive load | See section “Switching inductive loads”. |
| Braking voltage when switching off inductive loads | 50 VDC |
| Electrical isolation | Bus isolated from POWERLINK and channel Channel not isolated from channel |
| Any | Yes |
| 0 to 2000 m | No limitation |
| >2000 m | Reduction of ambient temperature by 0.5°C per 100 m |
| Degree of protection per EN 60529 | IP67 |
| Operation | -25 to 60°C |
| Derating | – |
| Storage | -40 to 85°C |
| Transport | -40 to 85°C |
| Width | 53 mm |
| Height | 155 mm |
| Depth | 42 mm |
| Weight | 360 g |
| M8 | Max. 0.4 Nm |
| M12 | Max. 0.6 Nm |
Reviews
Clear filtersThere are no reviews yet.