Fast delivery within 72 Hours
B&R 8BVI0880HWS0.004-1
Integrated uncontrolled and safe stopsIntegrated connection for motor holding brake and temperature sensor2 slots for ACOPOSmulti plug-in modules…
Request for Quote
Shipping & Delivery
-
Courier delivery
Our courier will deliver to the specified address
5-6 Days
From €20
-
DHL Courier delivery
DHL courier will deliver to the specified address
2-3 Days
From €40
-
Warranty 1 year
-
Free 30-Day returns
Description
Integrated uncontrolled and safe stopsIntegrated connection for motor holding brake and temperature sensor2 slots for ACOPOSmulti plug-in modules
ACOPOSmulti inverter module, 88 A, AS, wall mounting
Specification
| B&R ID code | 0xA69F |
|---|---|
| Dynamic node allocation (DNA) | Yes |
| Cooling and mounting type | Wall mounting |
| Slots for plug-in modules | 2 |
| CE | Yes |
| UKCA | Yes |
| Functional safety | Yes |
| UL | cULus E225616 Power conversion equipment |
| KC | Yes |
| Nominal | 5 to 40°C |
| Continuous power consumption | 65 kW |
| Switching frequency 5 kHz | 25 m |
| Switching frequency 10 kHz | 25 m |
| Switching frequency 20 kHz | 25 m |
| DC bus capacitance | 1980 µF |
| Variant | ACOPOSmulti backplane |
| Input voltage | 25 VDC ±1.6% |
| Input capacitance | 32.9 µF |
| Max. power consumption | 27 W + PSLOT1 + PSLOT2 + P24 V Out + PHoldingBrake |
| Quantity | 1 |
| DC bus voltage (UDC): 260 to 315 VDC | 25 VDC * (UDC/315) |
| DC bus voltage (UDC): 315 to 800 VDC | 24 VDC ±6% |
| Fuse protection | 250 mA (slow-blow) electronic, automatic reset |
| Continuous power per motor connection | 64 kW |
| Continuous current per motor connection | 88 Aeff |
| Starting at 500 m above sea level | 8.8 Aeff per 1000 m |
| Peak current | 176 Aeff |
| Nominal switching frequency | 5 kHz |
| Possible switching frequencies | 5 / 10 / 20 kHz |
| Insulation stress of the connected motor per IEC TS 60034-25:2004 | Limit value curve A |
| Overload protection | Yes |
| Short-circuit and ground fault protection | Yes |
| Max. output frequency | 598 Hz |
| U, V, W, PE | M8 threaded bolts |
| Shield connection | Yes |
| Flexible and fine-stranded wires | — |
| Terminal cable cross section dimension of shield connection | 12 to 50 mm |
| Output voltage | 24 VDC +5.8% / -0% |
| Continuous current per connection | 4.2 A |
| Max. internal resistance | 0.15 Ω |
| Extinction potential | Approx. 30 V |
| Max. extinction energy per switching operation | 3 Ws |
| Max. switching frequency | 0.5 Hz |
| Overload and short-circuit protection | Yes |
| Open-circuit monitoring | Yes |
| Undervoltage monitoring | Yes |
| Response threshold for open-circuit monitoring | Approx. 0.5 A |
| Response threshold for undervoltage monitoring | 24 VDC +0% / -4% |
| Circuit | Sink |
| Input - Inverter module | Yes |
| Input - Input | Yes |
| Maximum | 55°C |
| Input current at nominal voltage | Approx. 10 mA |
| Low | <5 V |
| High | >15 V |
| Enable 1 → 0, PWM off | Max. 20.5 ms |
| Enable 0 → 1, ready for PWM | Max. 100 µs |
| Modulation compared to ground potential | Max. ±38 V |
| OSSD signal connections | Permitted Max. test pulse length: 500 µs |
| Rising edge | 52 µs ±0.5 µs (digitally filtered) |
| Falling edge | 53 µs ±0.5 µs (digitally filtered) |
| Resistance range | 500 Ω to 5 kΩ |
| Discharge capacitance | 0.44 µF |
| Power dissipation relative to continuous apparent power | IE2 (10,25) 0.7% IE2 (50,25) 0.7% IE2 (10,50) 1% IE2 (50,50) 1% IE2 (90,50) 1% IE2 (10,100) 1.6% IE2 (50,100) 1.6% IE2 (90,100) 1.6% |
| Nominal losses in standby mode | 10.5 W |
| Hanging vertically | Yes |
| Horizontal, face up | Yes |
| Standing horizontally | No |
| Pollution degree per EN 61800-5-1 | 2 (non-conductive pollution) |
| Overvoltage category per EN 61800-5-1 | III |
| Degree of protection per EN 60529 | IP20 |
| Storage | 5 to 95% |
| Transport | Max. 95% at 40°C |
| Operation | 5 to 85% |
| Width | 213.5 mm |
| Height | 317 mm |
| Wall mounting | 263 mm |
| Weight | Approx. 10.9 kg |
| Module width | 4 |
Reviews
Clear filtersThere are no reviews yet.