Pepperl Fuchs UC4000-30GM-IUEP-IO-V15

Ultrasonic sensor. Single head system, IO-Link interface for service and process data, Programmable via DTM with PACTWARE, Switch output and analog output, Series: UC-30GM-IO, Operating voltage: 10 … 30 V DC , ripple 10 %SS 15 … 30 V voltage output, Interface type: IO-Link, Output type: 1 push-pull (4 in 1) output, short-circuit protected, reverse polarity protected Current output 4 mA … 20 mA or voltage output 0 V … 10 V configurable, UL approval: cULus Listed, Class 2 Power Source. Sensing range: 200 … 4000 mm. Adjustment range: 240 … 4000 mm. Dead band: 0 … 200 mm. Standard target plate: 100 mm x 100 mm. Transducer frequency: approx. 85 kHz. Response delay: minimum : 115 ms factory setting: 225 ms. Non-volatile memory: EEPROM. Write cycles: 100000. LED green: solid: Power onflashing: Standby mode or IO link communication. LED yellow 1: solid: Object in evaluation rangeflashing: Learning function, object detected. LED yellow 2: solid: Object in evaluation rangeflashing: Learning function, object detected. LED red: solid red: Errorred, flashing: program function, object not detected. Operating voltage: 10 … 30 V DC , ripple 10 %SS 15 … 30 V voltage output. No-load supply current: ≤ 60 mA. Power consumption: ≤ 1 W. Time delay before availability: ≤ 150 ms. Interface type: IO-Link. Protocol: IO-Link V1.0. Transfer rate: Acyclical: typical 54 Bit/s. Cycle time: min. 59.2 ms. Mode: COM2 (38.4 kBit/s). Process data width: 16 bit. SIO mode support: yes. Input/output type: 1 synchronization connection, bidirectional. 0 Level0 … 1 V1 Level4 V … UBInput impedance> 12 kΩOutput current 12 kΩ. Output current: < 12 mA. Pulse length: 0.5 … 300 ms (level 1). Pulse interval: ≥ 62 ms (level 0). Synchronization frequency: . Common mode operation≤ 16 HzMultiplex operation≤ 17 Hz / n , n = number of sensors , n ≤ 10 (factory setting: n = 5 ): . Common mode operation: ≤ 16 Hz. Multiplex operation: ≤ 17 Hz / n , n = number of sensors , n ≤ 10 (factory setting: n = 5 ). Output type: 1 push-pull (4 in 1) output, short-circuit protected, reverse polarity protected Current output 4 mA … 20 mA or voltage output 0 V … 10 V configurable. Rated operating current: 200 mA , short-circuit/overload protected. Voltage drop: ≤ 2.5 V. Resolution: current output: evaluation range [mm]/3200 but ≥ 0.35 mmvoltage output: evaluation range [mm]/4000 but ≥ 0.35 mm. Deviation of the characteristic curve: ≤ 0.2 % of full-scale value. Repeat accuracy: ≤ 0.1 % of full-scale value. Switching frequency: ≤ 2 Hz. Range hysteresis: 1 % of the adjusted operating range (default settings), programmable. Load impedance: current output: ≤ 300 Ohm voltage output: ≥ 1000 Ohm. Temperature influence: ≤ 1.5 % from full-scale value (with temperature compensation)≤ 0.2 %/K (without temperature compensation). Standard conformity: . StandardsEN IEC 60947-5-2:2020 IEC 60947-5-2:2019 EN 60947-5-7:2003 IEC 60947-5-7:2003: . Standards: EN IEC 60947-5-2:2020 IEC 60947-5-2:2019 EN 60947-5-7:2003 IEC 60947-5-7:2003. UL approval: cULus Listed, Class 2 Power Source. CCC approval: CCC approval / marking not required for products rated ≤36 V. Ambient temperature: -25 … 70 °C (-13 … 158 °F). Storage temperature: -40 … 85 °C (-40 … 185 °F). Connection type: Connector plug M12 x 1 , 5-pin. Degree of protection: IP67. Material: . HousingStainless steel 1.4305 / AISI 303 TPU PolyamidesTransducerepoxy resin/hollow glass sphere mixture; polyurethane foam: . Housing: Stainless steel 1.4305 / AISI 303 TPU Polyamides. Transducer: epoxy resin/hollow glass sphere mixture; polyurethane foam. Mass: 95 g. Dimensions: . Length100 mmDiameter40 mm: . Length: 100 mm. Diameter: 40 mm. Output 1: near switch point: 240 mm far switch point: 4000 mm Output mode: Window mode output behavior: NO contact. Output 2: near limit: 500 mm far limit: 2000 mm Output mode: rising ramp output behavior: Current output 4 mA … 20 mA. Beam width: wide