Fast delivery within 72 Hours
Pepperl Fuchs UC1000-18GS-IUEP-IO-V15
Ultrasonic sensor. Single head system, IO-Link Interface for process data, parameterization and diagnosis, Programmable via DTM with PACTWARE, Programmable via IrDA (infrared interface), Series: UC-18…
Request for Quote
Shipping & Delivery
-
Courier delivery
Our courier will deliver to the specified address
5-6 Days
From €20
-
DHL Courier delivery
DHL courier will deliver to the specified address
2-3 Days
From €40
-
Warranty 1 year
-
Free 30-Day returns
Description
Ultrasonic sensor. Single head system, IO-Link Interface for process data, parameterization and diagnosis, Programmable via DTM with PACTWARE, Programmable via IrDA (infrared interface), Series: UC-18GS, Operating voltage: 10 … 30 V DC , ripple 10 %SS, Interface type: IO-Link (via C/Q = Pin 4), Interface type: IrDA (infrared interface), Output type: 1 push-pull output , short-circuit protected , reverse polarity protected, Output type: 1 analog output 0 (4) … 20 mA or 1 analog output 0 … 10 V. Sensing range: 70 … 1000 mm. Adjustment range: 90 … 1000 mm. Dead band: 0 … 70 mm. Standard target plate: 100 mm x 100 mm. Transducer frequency: approx. 255 kHz. Response delay: minimum : 28 ms factory setting: 56 ms. Sensor cycle time: ≥ 14 ms (factory setting) ; programmable to 60 s. Temperature influence: with temperature compensation: ≤ ± 0.75% of the end value 10 min after switching on the sensor (factory setting) with enhanced temperature compensation: ≤ ± 0.75% of the end value 2 min after switching on the sensor without temperature compensation: 0.17 %/K. Non-volatile memory: EEPROM. Write cycles: 300000. LED green: solid: power onflashing: standby mode or IO-Link communication. LED yellow: solid: object in evaluation rangeflashing: switch point programming, object detected. LED red: solid: errorflashing: switch point programming, object not detected. Operating voltage: 10 … 30 V DC , ripple 10 %SS. No-load supply current: ≤ 60 mA. Power consumption: ≤ 1000 mW. Time delay before availability: ≤ 300 ms. Interface type: IO-Link (via C/Q = Pin 4). IO-Link revision: 1.1. Device profile: Smart Sensor Profile 2. Process data width: 32 bit. Device ID: 0x300604 (3147268). Transfer rate: COM2 (38.4 kBit/s). Min. cycle time: 3 ms. SIO mode support: yes. Compatible master port type: Class A Class B (use 3-pole adapter or 3-wire cable). Interface type: IrDA (infrared interface). Mode: point-to-point connection. Transfer rate: 115.2 kBit/s. Maximum communication distance: 5 cm. Input/output type: 1 synchronization connection, bidirectional. 0 Level0 … 1 V1 Level2.5 V … UBInput impedance> 22 kΩOutput currentcurrent source 22 kΩ. Output current: current source BR>PA, PC, POM and PBT plastic partsTransducerepoxy resin/hollow glass sphere mixture; polyurethane foam: . Housing: stainless steel (1.4305 / AISI 303)>BR>PA, PC, POM and PBT plastic parts. Transducer: epoxy resin/hollow glass sphere mixture; polyurethane foam. Installation position: any position. Mass: 45 g. Tightening torque, fastening screws: max. 30 Nm. Dimensions: . Length90 mmDiameter18 mm: . Length: 90 mm. Diameter: 18 mm. Output 1: near switch point: 90 mm far switch point: 1000 mm Output mode: Window mode output behavior: NO contact. Output 2: near limit: 90 mm far limit: 1000 mm Output mode: rising ramp output behavior: Current output 4 mA … 20 mA. Beam width: wide
Specification
General specifications
| Sensing range | 70 ... 1000 mm |
|---|---|
| Adjustment range | 90 ... 1000 mm |
| Dead band | 0 ... 70 mm |
| Standard target plate | 100 mm x 100 mm |
| Transducer frequency | approx. 255 kHz |
| Response delay | minimum : 28 ms factory setting: 56 ms |
| Sensor cycle time | ≥ 14 ms (factory setting) ; programmable to 60 s |
| Temperature influence | with temperature compensation: ≤ ± 0.75% of the end value 10 min after switching on the sensor (factory setting) with enhanced temperature compensation: ≤ ± 0.75% of the end value 2 min after switching on the sensor without temperature compensation: 0.17 %/K |
Memory
| Non-volatile memory | EEPROM |
|---|---|
| Write cycles | 300000 |
Indicators/operating means
| LED green | solid: power onflashing: standby mode or IO-Link communication |
|---|---|
| LED yellow | solid: object in evaluation rangeflashing: switch point programming, object detected |
| LED red | solid: errorflashing: switch point programming, object not detected |
Electrical specifications
| Operating voltage | 10 ... 30 V DC , ripple 10 %SS |
|---|---|
| No-load supply current | ≤ 60 mA |
| Power consumption | ≤ 1000 mW |
| Time delay before availability | ≤ 300 ms |
Interface 1
| Interface type | IO-Link (via C/Q = Pin 4) |
|---|---|
| IO-Link revision | 1.1 |
| Device profile | Smart Sensor Profile 2 |
| Process data width | 32 bit |
| Device ID | 0x300604 (3147268) |
| Transfer rate | COM2 (38.4 kBit/s) |
| Min. cycle time | 3 ms |
| SIO mode support | yes |
| Compatible master port type | Class A Class B (use 3-pole adapter or 3-wire cable) |
Interface 2
| Interface type | IrDA (infrared interface) |
|---|---|
| Mode | point-to-point connection |
| Transfer rate | 115.2 kBit/s |
| Maximum communication distance | 5 cm |
Input/Output
| Input/output type | 1 synchronization connection, bidirectional |
|---|---|
| 0 Level0 ... 1 V1 Level2.5 V ... UBInput impedance> 22 kΩOutput currentcurrent source < 2.5 mAPulse length≥ 1 ms with external control, low active | |
| 0 Level | 0 ... 1 V |
| 1 Level | 2.5 V ... UB |
| Input impedance | > 22 kΩ |
| Output current | current source < 2.5 mA |
| Pulse length | ≥ 1 ms with external control, low active |
| Synchronization frequency | |
| Common mode operation≤ 71 HzMultiplex operation≤ 71 Hz / n , n = number of sensors , n ≤ 10 | |
| Common mode operation | ≤ 71 Hz |
| Multiplex operation | ≤ 71 Hz / n , n = number of sensors , n ≤ 10 |
Switching output
| Output type | 1 push-pull output , short-circuit protected , reverse polarity protected |
|---|---|
| Rated operating current | 100 mA , short-circuit/overload protected |
| Switching frequency | factory setting: 10 Hz programmable to 23 Hz |
| Voltage drop | ≤ 2.5 V |
| Repeat accuracy | ≤ ± 0.1 % of full-scale value |
| Range hysteresis | 1 % of the adjusted operating range (default settings), programmable , min. 1 mm |
| Off-state current | ≤ 100 µA |
Analog output
| Output type | 1 analog output 0 (4) ... 20 mA or 1 analog output 0 ... 10 V |
|---|---|
| Resolution | current output: evaluation range [mm]/3200 but ≥ 0.35 mmvoltage output: evaluation range [mm]/4000 but ≥ 0.35 mm |
| Deviation of the characteristic curve | ≤ ± 1 % of full-scale value |
| Repeat accuracy | ≤ ± 0.1 % of full-scale value |
| Load resistor | current output: ≤ 500 Ω voltage output: ≥ 1000 Ω |
Compliance with standards and directives
| Standard conformity | |
|---|---|
| StandardsEN IEC 60947-5-2:2020 IEC 60947-5-2:2019 EN 60947-5-7:2003 IEC 60947-5-7:2003 IEC 61131-9:2013 | |
| Standards | EN IEC 60947-5-2:2020 IEC 60947-5-2:2019 EN 60947-5-7:2003 IEC 60947-5-7:2003 IEC 61131-9:2013 |
Approvals and certificates
| UL approval | cULus Listed, Class 2 Power Source |
|---|---|
| CCC approval | CCC approval / marking not required for products rated ≤36 V |
Ambient conditions
| Ambient temperature | -25 ... 70 °C (-13 ... 158 °F) |
|---|---|
| Storage temperature | -40 ... 85 °C (-40 ... 185 °F) |
Mechanical specifications
| Connection type | Connector plug M12 x 1 , 5-pin |
|---|---|
| Degree of protection | IP67 |
| Material | |
| Housingstainless steel (1.4305 / AISI 303)>BR>PA, PC, POM and PBT plastic partsTransducerepoxy resin/hollow glass sphere mixture; polyurethane foam | |
| Housing | stainless steel (1.4305 / AISI 303)>BR>PA, PC, POM and PBT plastic parts |
| Transducer | epoxy resin/hollow glass sphere mixture; polyurethane foam |
| Installation position | any position |
| Mass | 45 g |
| Tightening torque, fastening screws | max. 30 Nm |
| Dimensions | |
| Length90 mmDiameter18 mm | |
| Length | 90 mm |
| Diameter | 18 mm |
Factory settings
| Output 1 | near switch point: 90 mm far switch point: 1000 mm Output mode: Window mode output behavior: NO contact |
|---|---|
| Output 2 | near limit: 90 mm far limit: 1000 mm Output mode: rising ramp output behavior: Current output 4 mA ... 20 mA |
| Beam width | wide |
Reviews
Clear filtersThere are no reviews yet.