Pepperl Fuchs OMT50-R100-2EP-IO-V31-L

Distance sensor. Measurement to object, 50 mm detection range, red laser light, laser class 1, measured value via IO-Link, 2 x push-pull output, M8 plug, Miniature design with versatile mounting options, Space-saving distance sensors in small standardized design, Multi Pixel Technology (MPT) – exact and precise signal evaluation, DuraBeam Laser Sensors – durable and employable like an LED, IO-Link interface for service and process data. Measuring range: 20 … 50 mm. Reference target: standard white, 100 mm x 100 mm. Light source: laser diode. Light type: modulated visible red light. Laser nominal ratings: . NoteLASER LIGHT , DO NOT STARE INTO BEAMLaser class1Wave length680 nmBeam divergence> 5 mrad d63 d63 5 mrad d63 d63 < 1 mm in the range of 50 mm … 250 mm. Pulse length: 3 µs. Repetition rate: approx. 3 kHz. max. pulse energy: 15.2 nJ. Angle deviation: max. +/- 1.5 °. Diameter of the light spot: approx. 0.5 mm at a distance of 50 mm. Opening angle: approx. 0.6 °. Ambient light limit: EN 60947-5-2 : 30000 Lux. Resolution: 0.01 mm. MTTFd: 560 a. Mission Time (TM): 20 a. Diagnostic Coverage (DC): 0 %. Operation indicator: LED green:constantly on – power onflashing (4Hz) – short circuitflashing with short break (1 Hz) – IO-Link mode. Function indicator: LED yellow:constantly on – switch output activeconstantly off – switch output inactive. Control elements: Teach-In key. Control elements: 5-step rotary switch for operating modes selection. Operating voltage: 10 … 30 V DC. Ripple: max. 10 %. No-load supply current: < 25 mA at 24 V supply voltage. Protection class: III. Interface type: IO-Link ( via C/Q = pin 4 ). IO-Link revision: 1.1. Device profile: Smart Sensor. Device ID: 0x110902 (1116418). Transfer rate: COM2 (38.4 kBit/s). Min. cycle time: 3 ms. Process data width: Process data input 3 ByteProcess data output 2 Bit. SIO mode support: yes. Compatible master port type: A. Switching type: The default setting is: C/Q – Pin4: NPN normally open, PNP normally closed, IO-Link Q2 – Pin2: NPN normally-open, PNP normally-closed. Signal output: 2 push-pull (4 in 1) outputs, short-circuit protected, reverse polarity protected, overvoltage protected. Switching voltage: max. 30 V DC. Switching current: max. 100 mA , resistive load. Usage category: DC-12 and DC-13. Voltage drop: ≤ 1.5 V DC. Response time: 2 ms. Communication interface: IEC 61131-9. Product standard: EN 60947-5-2. Laser safety: EN 60825-1:2014. Temperature drift: 20 µm/K. Warm up time: 5 min. Repeat accuracy: ≤ 0.1 mm. Linearity error: ± 0.2 mm. UL approval: E87056 , cULus Listed , class 2 power supply , type rating 1. FDA approval: IEC 60825-1:2014 Complies with 21 CFR 1040.10 and 1040.11 except for conformance with IEC 60825-1 Ed. 3 as described in Laser Notice 56, dated May 8, 2019.. Ambient temperature: 10 … 60 °C (50 … 140 °F). Storage temperature: -40 … 70 °C (-40 … 158 °F). Degree of protection: IP67 / IP69 / IP69K. Connection: M8 x 1 connector, 4-pin. Material: . HousingPC (Polycarbonate)Optical facePMMA: . Housing: PC (Polycarbonate). Optical face: PMMA. Mass: approx. 10 g. Dimensions: . Height44.5 mmWidth11 mmDepth21.5 mm: . Height: 44.5 mm. Width: 11 mm. Depth: 21.5 mm